on the track, TIME REMAINING on the disc and TIME RE-
MAINING on the track. Time is measured in minutes, sec-
onds and frames.
PGM: Allows you to create a set playlist. To program a set
list into the CDX-2410 memory, begin by stopping the unit
from play and pressing PGM to begin the set list. Select a
track by using the track selection rotary to scan to the first
track to be placed in the set list. When you have selected the
proper track press PGM and the CDX-2410 will be ready to
set your next selection. Repeat the previous steps until you
have completed your play list, then press play to begin the
set list.
REPEAT: Press the repeat button once to engage 1 once or
repeat the selected track. Press REPEAT again to engage
ALL setting, which will repeat all the tracks on the CD. Press
REPEAT again to disengage the repeat function
SINGLE: Pressing the SINGLE button engages SINGLE
mode, in this mode the CDX-2410 will play one song and
then stop. Pressing the SINGLE button again will then acti-
vate CONTINUOUS mode causing the unit to play continu-
ously (after the last track, the unit will return to the first track
of the disc and continue to play).
TIME: The TIME button switches the time display between
three available sources, these three are TIME ELAPSED on
the track, TOTAL REMAIN on the disc and REMAIN on the
track. TIME ELAPSED indicates how much time has cur-
rently gone by since the play button was pressed, TOTAL
REMAIN will count down the time remaining on the entire
disc and REMAIN counts down the time that is left before the
end of the track.
PITCH: Hold the PITCH button to activate the PITCH CON-
TROL SLIDE. Press the PITCH button to switch between +/-
4%, 8%, and 16% pitch ranges that can be controlled through
the use of the PITCH CONTROL SLIDER. Hold the PITCH
button again to deactivate this mode.
PITCH CONTROL SLIDE: Moving the PITCH CONTROL
SLIDE up or down will change the pitch perc/ - 4,
8, or 16%.
PITCH BEND: Pushing the PITCH BEND BUTTONS will au-
tomatically raise the pitch up to +16% or lower the pitch down
to -16% from the existing pitch setting. Releasing the buttons
will return the pitch to the original pitch setting. You can use
this function to match the beat when mixing from one song
to another.
LOOP SECTION: A LOOP repeats the section between the
entry point (LOOP IN) and the exit point (LOOP OUT).
A. To set a loop while the unit is playing, start by pressing
the LOOP IN BUTTON (it will light up)
B. When you reach the desired end loop point press the
LOOP OUT BUTTON (it will also light up). The LOOP IN
and LOOP OUT buttons will blink. The loop will continue
playing until you press the LOOP OUT BUTTON again al-
lowing the music to continue from that point on.
C. To re-engage the loop you must press the RELOOP
BUTTON.
D. When you have released your loop the LOOP IN and
LOOP OUT BUTTON buttons will turn OFF and the will re-
main lit to indicate that your loop is stored in the CDX-2410
memory.
E. Pressing the LOOP IN BUTTON again while the unit is
playing will erase the previously saved loop while saving
your new loop entry point.
F. Press LOOP OUT to exit the loop and save a new com-
plete loop.
G. Press RELOOP to return to the beginning of the previ-
ously saved loop from normal play. Press RELOOP repeat-
edly to cause the loop to stutter.
NOTE: THE FIRST LOOP WILL HAVE A PAUSE AT THE EXIT
POINT, WHILE ALL OTHERS WILL BE SEAMLESS.
PLAY / PAUSE: Each press of the PLAY / PAUSE BUTTON
causes the operation to change from PLAY to PAUSE or from
PAUSE back to PLAY. The PLAY/PAUSE BUTTON remains lit
when in PLAY mode, while it blinks in PAUSE mode.
CUE: To set a CUE point, press the PLAY/PAUSE BUTTON
while a file is playing and use the JOG WHEEL to locate a
desired CUE point. Pressing the PLAY/PAUSE BUTTON again
will set the CUE point. While the unit is playing and after the
cue point has been programmed, pressing CUE will cause the
CD player to enter the PAUSE mode (PLAY/PAUSE BUTTON
blinks) at the programmed cue point (the CUE LED is lit). Hold-
ing down the CUE button changes the function to preview, and
allows you to stutter start or play from the programmed CUE
POINT. Releasing the CUE button will return the CD to the
preset CUE point.
TRACK SELECTION ROTARY: The TRACK SELECTION RO-
TARY allows you to select the next or previous track by either
turning it clockwise to go forward or counter-clockwise to go
back. Select the track desired by pressing the TRACK SELEC-
TION ROTARY.
NOTE: ONCE YOU HAVE SKIPPED TO ANOTHER TRACK,
YOU MAY NOT GO BACK TO YOUR PROGRAMMED CUE
POINT. YOU MUST BEGIN YOUR CUE SELECTION OVER
AGAIN, THE CUE WILL BE PRESET TO THE BEGIN-NING
OF THE NEWLY SELECTED TRACK.
BRAKE: To engage the BRAKE function, press the BRAKE
button, then the PAUSE button to perform the brake effect. To
restart the song, press the PAUSE button.
REVERSE: When the REVERSE button is pressed, the file
that is currently playing begins to play in reverse mode.
5
CDX-2410
10
11
12
13
14
15
17
16
18
19
20
21
22
