After a few TAPS the unit will determine the average BEATS PER
MINUTE of the track.
20) MASTER TEMPO: Pressing the MASTER TEMPO button sets
the tempo of the track in the corresponding channel as the domi-
nant tempo, against which other tracks can be set.
21) SYNC: Pressing the SYNC button sets the tempo of the track
in the corresponding channel to the tempo of the track in the other
channel. Set the MASTER TEMPO, then press the SYNC button
to match the tempos.
22) EFFECTS SELECTOR: Press the EFFECTS SELECTOR but-
ton to choose which effect to apply to the engaged track.
23) EFFECT ON: Pressing the EFFECT ON button applies the
effect chosen by the EFFECTS SELECTOR (22) to the currently
playing/ loaded track.
24) SAMPLER PLAY: Pressing the SAMPLER PLAY button en-
gages the sampler function on your unit.
SAMPLER DISPLAY (24a): The SAMPLER DISPLAY section
contains a range of LEDs numbered 1-12 that illuminate based
upon the selected sample.
SAMPLER SELECTOR (24b): The SAMPLER SELECTOR
knob is used to select a specific sample.
SAMPLER VOLUME (24c): The SAMPLER VOLUME knob is
rotated to effect the overall level of the sample. Turning the
knob clockwise raises the volume of the sample, and turning the
knob counter-clockwise lowers the volume of the sample.
25) LOOP IN/ LOOP OUT: A LOOP repeats the section between
the entry point (IN) and the exit point (OUT). To set a loop while the
unit is playing, start by pressing the LOOP IN button (it will light up)
and when you reach the desired end loop point press the LOOP
OUT button (it will also light up and both will flash). The loop will
continue playing until you press LOOP OUT.
Pressing the IN BUTTON again while the unit is playing will erase
the previously saved loop while saving your new loop entry point.
Press OUT to exit the loop and save a new complete loop.
26) LOOP ADJUST 1/8 / LOOP ADJUST 16: Pressing the LOOP
ADJUST buttons adjusts the length of the selected loop. LOOP
ADJUST 1/8 halfs the set loop’s length. LOOP ADJUST 16 dou-
bles the set loop’s length.
27) PARAMETER 1: The PARAMETER 1 rotary knob adjusts the
value associated with Parameter 1 of the selected effect.
28) PARAMETER 2: The PARAMETER 2 rotary knob adjusts the
value associated with Parameter 2 of the selected effect.
29) CROSS FADER SLOPE: The CROSS FADER SLOPE rotary
adjustment allows you to alter how the channels come in and out
when the crossfader is used. When set to the RIGHT, when the
fader is moved, the channel will go from silent, to full volume very
quickly. When set to LEFT, the channel will go from silent, to full
volume gradually.
CTRL-ONE - EN
9
Additional Information
Specifications
Especificaciones • Caractéristiques techniques • Technische Daten
Troubleshooting
If you experience an error while using the unit, here are a few
explanations of those errors and how they can be corrected. For
a more complete troubleshooting guide, consult our website at
http://www.geminidj.com.
- Check the USB cable that is being used to connect the PC to the
CTRL-ONE.
- If the device is powered by an external power supply, make sure
that the unit is receiving power.
Specifications
Type of unit................................................. USB MIDI controller
Power.................................................................. USB-Powered
5V 1000 mA DC Adaptor (not included)
Connector type....................................................... USB Type B
USB protocol support..................... 1.0, 1.1, and 2.0 (Hi-Speed)
Weight............................................................................ 3.87 lbs
1.8 kg
Dimensions.......................................... 14 x 10.25 x 1.75 inches
360 x 260 x 45 mm
SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE
WITHOUT NOTICE FOR PURPOSE OF IMPROVEMENT.
