can further modify the sound output of this channel by
adjusting the rotary
GAIN
(54),
HIGH
(56),
MID
(57),
LOW
(58) controls located to the left of the
CH 5 SLIDE CON-
TROL
(59).
NOTE: FOR OPTIMAL PERFORMANCE, BEGIN PROGRAM MIX WITH
ROTARY GAIN (26, 33, 40, 47, 54) CONTROLS SET TO ZERO
(ROTATE IT COUNTERCLOCKWISE TO THE LEFT POSITION).
MAKE ALL ADJUSTMENTS IN SOUND OUTPUT WITH THE USE OF
YOUR CHANNEL SLIDE CONTROLS (31, 45, 59, 38, 52), ZONE (66),
BALANCED MASTER (63), AND MASTER (64) VOLUME ROTARY
CONTROLS. THIS WILL PREVENT SIGNAL OVERLOAD AND
DECREASE DISTORTION. ONCE YOU HAVE MODIFIED YOUR
SOUND AND WOULD LIKE TO INCREASE THE OUTPUT OF YOUR
SOUND, THEN YOU MAY ADJUST THE ROTARY GAIN CONTROL IF
NEEDED.
7.
CUE:
By connecting a set of headphones to the
HEAD-
PHONE
(60) jack, you can monitor any or all channels.
Press
CUE
buttons (27, 34, 41, 48, 55) for
CH 1
through
CH 5
to assign the Channel(s) to be monitored. The
respective
CUE LED
indicators will glow when in use. Use
the rotary
CUE VOLUME CONTROL
(61) to adjust the
cue volume without changing the overall mix. By moving
the
CUE/PGM FADER CONTROL
(62) to the
LEFT
you
will be able to monitor the assigned cue signal. Moving
the control to the
RIGHT
allows you to monitor
PGM
out-
put. Moving the control to the
MIDDLE
allows cue mix with
PGM
.
8.
ASSIGN:
There are
2 ROTARY CONTROLLED ASSIGN
SWITCHES
(67, 68), each having 5 settings 1, 2, 3, 4 and
5. The
LEFT ASSIGN
(67) control allows you to direct CH
1, 2, 3, 4 or 5 through the
LEFT
side of the
CROSSFAD-
ER
(69). The
RIGHT ASSIGN
(68) control allows you to
direct CH 1, 2, 3, 4 or 5 through the
RIGHT
side of the
CROSSFADER
(69).
9.
CROSSFADER SECTION:
The
CROSSFADER
(69)
allows you to mix from one source to another. The
MM-03
features an
ASSIGNABLE CROSSFADER
(69). The
rotary controlled
ASSIGN SWITCHES
(67, 68) allow you
to select which channel will play through each side of the
CROSSFADER
(69). The
CROSSFADER
(69) in your unit
is removable and if the need arises can be easily
replaced. Your
Gemini
mixer comes with an
RG-45
(RAILGLIDE™) Dual-Rail Crossfader
.
Rail Glide™
crossfaders
have internal dual stainless steel rails that
allow the slider to ride smoothly and accurately from end
to end. Also available is our
RG-45 PRO (PROGLIDE™)
Dual-Rail
Crossfader. This unique crossfader features, a
special curve designed for scratch mixing. Just purchase
one from your
Gemini
dealer and follow the instructions:
10.
OUTPUT SELECTION CONTROL:
Once you are com-
fortable with the sound level of your music you may adjust
the volume with the
MASTER
(64) rotary control. You may
adjust the volume of the zone output with the
ZONE
(66)
rotary control. You may also adjust the balance from left to
right with the
BALANCED MASTER
(63) rotary control.
11.
MIC SECTION:
Plug your main mic into the
MIC 1
com-
bination
XLR-1/4"
input (20) located on the face panel.
The rotary controls for
HIGH
(22) and
LOW
(23) for
MIC
1
(20) allow you to adjust the tone of
MIC 1
(20). The
MIC
1
rotary volume control (21), above the
HIGH
(22)/
LOW
(23) controls, adjust the decibel level of
MIC 1
(20). You may also plug a second and third mic into
the rear panel's
MIC 2
(19) and
MIC 3
(10)
¼" jacks
. The
tone and decibel level of
MIC 2
(19) and
MIC 3
(10) are
controlled by the
CH 1
(31) and
CH 4
(52) slide controls,
the
3 BAND ROTARY EQ
(
HIGH
(28, 49),
MID
(29, 50),
LOW
(30, 51)) controls and
GAIN
(26, 47) rotary controls,
respectively.
12.
TALKOVER:
The purpose of the
AUTO TALKOVER
MODE
is to allow the program playing to be muted so that
the mic may be heard above the music. The
MIC/TALKOVER SWITCH
(24) controls
MIC 1
(20) with
3
settings:
- When the
MIC/TALKOVER SWITCH
(24) is in the
BOT-
TOM
position,
MIC 1
(20) and
TALKOVER MODE
are all
OFF
.
- When the
MIC/TALKOVER SWITCH
(24) is in the
CEN-
TER
position,
MIC 1
(20) is
ON
and
TALKOVER MODE
is
OFF
. The
MIC ON LED INDICATOR
glows when
MIC 1
(20) is
ON
.
- When the
MIC/TALKOVER SWITCH
(24) is in the
TOP
position,
MIC 1
(20) is
ON
and
TALKOVER MODE
is
ON
,
and the volume of all sources except
MIC 1
(20) inputs is
lowered by -16 dB.
13.
VU METER:
The
VU METER
(65) indicates the pro-
gram output level of the
MASTER
(3) left and right stereo
levels.
SPECIFICATIONS:
INPUTS:
Phono............................................................3 mV, 47 KOhm
Line...........................................................150 mV, 27 KOhm
MIC 1, MIC 2, & MIC 3.................1.5 mV, 1 K Ohm Balanced
MIC 1 Bass.................................................................± 12dB
MIC 1 High..................................................................± 12dB
OUTPUTS:
Amp/Zone.................................................0 dB 1V, 400 Ohm
Max...........................................................20V Peak-to-Peak
Rec..............................................................225 mV, 5 KOhm
GENERAL:
Frequency Response..........................20Hz - 20KHz +/- 2 dB
Distortion...................................................................< 0.02%
S/N Ratio...................................................Better Than 80 dB
Talkover Attenuation....................................................-16 dB
Headphone Impedance.............................................16 Ohm
Power Source.................................115/230V, 50/60Hz, 20W
Unit Dimensions..................................W 19" x H 4" x D 7.42"
....................................................(482.6 x 101.6 x 188.6 mm)
Weight.........................................................8.84 lbs (4.01kg)
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTIFICATION
FOR IMPROVEMENT.
Replaceable Crossfader
1. Unscrew the outside FADER plate screws (B).
- Do not touch INSIDE
SCREWS (C).
2. Carefully remove old
Crossfader and unplug
CABLE (D).
3.Plug new Crossfader into
CABLE (D) and place back
into mixer.
4. Screw Crossfader to mixer
with the FADER PLATE
SCREWS (B).
(5)
Summary of Contents for MM-03
Page 3: ... 3 ...
