Gemini PDM-16 Service Manual Download

Page: 6 / 12

Page 5

in the bottom position, MIC 1 and MIC 2 and talkover are off. When
the

MIC/TALKOVER SWITCH (7)

is in the center position MIC 1 and

MIC 2 are on, the

MIC INDICATOR (6)

will glow, but talkover is off.

When the

MIC/TALKOVER SWITCH (7)

is in the top position, MIC 1

and MIC 2 and talkover will be on and the volume of all sources
except the Mic inputs are lowered by 16 dB. The

TREBLE (2)

and

BASS (3)

controls allow you to fully adjust the tone of MIC 1 and MIC

MIC 1 LEVEL (5)

controls the level of MIC 1. The

MIC 2 LEVEL

(4)

controls the level of MIC 2.

10. CUE SECTION: By connecting a set of headphones to the

HEADPHONE (35)

jack, you can monitor any or all of the channels.

Press the

CUE ASSIGN (20)

buttons for channels 1 - 4 to select the

channel or channels to be monitored and their respective LED
indicators will glow. Use the

CUE LEVEL (34)

control to adjust the

cue volume without effecting the overall mix. By moving the

CUE

PGM PAN (33)

control to the left you will be able to monitor the

assigned cue signal. Moving the control to the right will monitor the
PGM (program) output. Moving to the right will monitor the PGM
(program) output.

11. DISPLAY: The

DISPLAY (21)

indicates the

MASTER

output left and

right levels.

12. SOUND EFFECTS SECTION: Six different sound effects (UFO, TRON

BLAST, SIREN, GAS, MACHINE GUN and EMERGENCY) may be
added to your mix by depressing the

SOUND EFFECTS CONTROL

BUTTONS (25)

. The volume of the effects can be adjusted using the

EFFECTS LEVEL CONTROL (27)

. The pitch of the effects can be

increased or decreased using the

EFFECTS SPEED CONTROL (26)

Specifications

INPUTS:
DJ Mic....................................................1.5mV 2Kohm balanced
Phono.........................................................................3mV 47Kohm
Line.......................................................................150 mV 27Kohm

OUTPUTS:
Amp/Booth......................................................0 dB 1V 400ohm
Max..............................20V Peak to Peak
Rec...........................................................................225mV 5Kohm

MIC 1 & MIC 2:
DJ Mic....................................................1.5mV 2Kohm balanced
Bass......................................................................................± 12dB
High.......................................................................................± 12dB

GENERAL:
Frequency Response....................................20Hz - 20KHz +/- 2dB
Distortion................................................................................0.02%
S/N Ratio...............................................................better than 80dB
Talkover Attenuation..............................................................-16dB
Headphone Impedance.........................................................16ohm
Power Source.............................................115/230V 50/60Hz 10W
Dimensions................................................19”w x 4”h x 9”d
Weight........................................................................10.17 lbs

Description

Part #

Cabinet Parts and Packing

1
2
4
5
6
7
8
9

10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36

37
38
39
40
41
42
43

Item #

Parts Lists

002-210
034-001
032-018
021-763
022-322
022-305
049-199
023-674
002-531
002-532
002-704
002-715
003-102
003-110
148-236
148-239
003-994
003-970
003-373
003-969
003-986
003-975
003-564
047-474
049-206
159-201
156-216
159-171
159-196
146-710
102-007
101-008
102-025
107-015
110-172A

111-043A
111-044A
111-046A
111-049A
111-050
111-051A
111-053A

131-081

PANEL CONTROL
PANEL REAR
COVER BOTTOM
BRACKET VR
HOLDER X-FADER
PROTECTOR PLATE FOR 115/230V SWITCH
SOUND CONTROL KEY
SWING LEVEL
KNOB PUSH (SMALL)
BUSHING FOR KNOB (SMALL)
KNOB SLIDE (BIG)
KNOB SLIDE
KNOB ROTARY (ASSIGN)
KNOB ROTARY (B)
KNOB INLAY (BLACK)
KNOB INLAY (GRAY)
EQ VR INLAY
TRIM VR
INLAY PLATE
HOLDER LED 3f LED(17mm)
HOLDER LED
HOLDER LED
WASHER XLR
PCB SPACER SUPPORT
PAD FOOT
BNC DUST PROOF CLOTH
DUST PROOF CLOTH (KNOB-SWING)
DUST PROOF CLOTH (VR)
FADER DUST PROOF CLOTH
GND SCREW
PAN-HEAD MACHINE SCREW; PMS 2X4(B)
FLAT-HEAD MACHINE SCREW; FMS 2X4 (Y)
PAN-HEAD MACHINE SCREW; PMS 2.6X4(B)
BAND-HEAD MACHINE SCREW; BMS 3X2X4
BAND-HEAD TAPPING SCREW/TWIN SCREW;
BTS-2 3X8(AB) TWIN
FLAT-HEAD TAPPING SCREW; FTS-3 3X6(AB)
BAND-HEAD TAPPING SCREW; BTS-3 3X10(AB)
BAND-HEAD TAPPING SCREW; BTS-3 3X6(AB)
FLAT-HEAD TAPPING SCREW; FTS-3 3X12(AB)
FLAT-HEAD TAPPING SCREW; FTS-3 3X12(Y)
BAND-HEAD TAPPING SCREW; BTS-3 3X5(AB)
BAND-HEAD TAPPING SCREW/TW-E;
BTS-3/TW-E 3X6(AB)
NUT/WASHER 3mm

262-044

262-045

262-047

262-046

262-048

262-049

PRINTED CIRCUIT BOARD PDM-24S-1:
IN/OUT
PRINTED CIRCUIT BOARD PDM-24S-2:
MAIN
PRINTED CIRCUIT BOARD PDM-18-3:
EFFECT
PRINTED CIRCUIT BOARD PDM-24S-4:
FADER
PRINTED CIRCUIT BOARD PDM-18-5:
PHONES
PRINTED CIRCUIT BOARD PDM-18-6

Description

Part #

Printed Circuit Boards

Item #