(5)
(5)
(5)
(5)
(5)
INTRODUCTION:
Congratulations on purchasing a
Gemini XL-120MKII
turntable. This
state of the art turntable includes the latest features. Prior to use, we
suggest that you carefully read all the instructions.
FEATURES:
•
S-Shaped Tone Arm
•
Anti Skate Adjustment
•
Strobe Illuminator
•
Start/Stop Button
•
Dust Cover
•
Adjustable Pitch +/- 6%
•
Removeable Headshell & Cartridge Included
•
33/45 RPM
•
“G” Slipmat
PRECAUTIONS:
1. Read all operating instructions before using this equipment.
2. To reduce the risk of electrical shock, do not open the unit. There are
NO USER REPLACEABLE PARTS INSIDE
. Please contact the Gemini
Service Department or your authorized dealer to speak to a qualified
service technician.
3. Tone Arm bearings are factory set and sealed. Any attempt at
adjustment will void the warranty.
4. Be sure that all AC power is OFF while making connections.
5. Cables should be low capacitance, shielded and of proper length. Make
sure that all plugs and jacks are tight and properly connected.
6. Always begin with the audio level faders/volume controls set at
minimum and the speaker volume control(s) set to OFF. Wait 8 to 10
seconds prior to turning up the speaker volume to prevent the transient
“POP” that could result in speaker/crossover damage.
7.
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE
.
8.
DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY
CONTROLS OR SWITCHES
.
PARTS CHECKLIST:
Turntable unit................................................................................................1
Dust cover hinges........................................................................................2
Turntable platter............................................................................................1
45 RPM adapter.............................................................................................1
Rubber mat...................................................................................................1
Counter balance...........................................................................................1
Dust cover....................................................................................................1
Headshell.......................................................................................................1
Cartridge.......................................................................................................1
ASSEMBLY AND SET-UP:
NOTE: SEE FIG. 1 FOR PART NUMBERS AND LOCATIONS.
VOLTAGE SELECTION:
Rotate the
PLATTER (2)
until the
VOLTAGE SELECTOR (3)
(located on
the
TURNTABLE BASE (1)
) is visible through one of the platter holes.
Make sure that the
VOLTAGE SELECTOR (3)
switch is set to the
correct voltage.
WARNING: IF YOU TRY TO OPERATE THE TURNTABLE WITH THE
INCORRECT VOLTAGE SETTING, IT CAN DAMAGE YOUR
TURNTABLE.
ATTACHING THE TURNTABLE BELT:
The
TURNTABLE BELT (4A)
comes attached to the
PLATTER (2)
and
the
MOTOR SPINDLE (4B)
but can some times detach in shipping.
Rotate the
PLATTER (2)
and look through the platter holes to check if
belt detached. If the belt is not wrapped tightly around the platter and
the
MOTOR SPINDLE (4B)
, you need to reattach it.
1. First, place a screwdriver in the center of
LOCKING WASHER (4C)
around the
CENTER SPINDLE (4)
and gently pry the washer off.
2. Remove the platter and wrap the belt around the inner circle under the
platter.
DO NOT STRETCH OUT THE BELT
.
3. Replace the platter and rotate the
PLATTER (2)
until the
MOTOR
SPINDLE (4B)
is visible, then fit your fingers in hole on the top of the
PLATTER (2)
, feel for and grab the rubber belt and attach to the motor
spindle.
4. Replace the locking washer.
TURNTABLE INSTALLATION:
1. Put the
RUBBER MAT (5)
on the
PLATTER (2)
.
2. Set the
TURNTABLE BASE (1)
on a flat, level surface free of vibration.
Use the turntable feet to horizontally stabilize the unit.
3. Try to place the unit as far away from the speakers as possible.
4. Keep the unit away from direct exposure to the sun, heat, moisture or dirt.
5. Keep the unit well ventilated.
CARTRIDGE INSTALLATION:
(SEE FIG. 2)
Because all cartridges have their own designs, please refer to your
particular cartridge’s instructions to insure proper installation.
1. Connect the lead wires to the cartridge terminals. For your
convenience, the terminals of most cartridges are color coded. Connect
each lead wire to the terminal of the same color.
White (L+)...........................................................................Left C
Blue (L-)..............................................................................Left Channel -
Red (R+)...........................................................................Right C
Green (R-).........................................................................Right Channel -
2. Mount the cartridge in the
HEADSHELL (6)
and tighten it with the
screws included with the cartridge.
ATTENTION STANTON 680 CARTRIDGE USERS
When using a Stanton 680 or similar cartridge, where the body is
grounded to a cartridge terminal, remove the grounding strap from the
cartridge body to the cartridge ground terminal. Failure to do this may
result in excessive hum.
HEADSHELL INSTALLATION:
Insert the
HEADSHELL (6)
into the front of the tubular
TONE ARM (7)
. While
holding the
HEADSHELL
firmly in a horizontal position, turn the
LOCKING NUT
(8)
counter clockwise until the
HEADSHELL
is locked in place.
COUNTERWEIGHT INSTALLATION:
(SEE FIG. 3A & 3B)
1. Slide the
COUNTERWEIGHT (9)
onto the rear of the
TONE ARM (7)
with the numbered stylus gauge facing forward.
2. Twist the
COUNTERWEIGHT (9)
lightly counter clockwise, to screw it
onto the rear of the
TONE ARM (7).
ADJUSTING HORIZONTAL ZERO (0) BALANCE AND
STYLUS PRESSURE:
1. Without touching the stylus tip, remove the stylus protector (if your
cartridge has a detachable one).
2. Release the
ARM CLAMP (10)
and lift the
TONE ARM (7)
off the
ARM
REST (11)
.
3. Counter clockwise advancement of the
COUNTERWEIGHT (9)
will
cause the cartridge side of the
TONE ARM (7)
to be lowered. Clock
