background image

CPE7000 Outdoor Dual Mode - Quick Installation Guide 

 

Federal Communication Commission Interference Statement 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits 

are  designed  to  provide  reasonable  protection  against  harmful  interference  in  a  residential  installation.  This  equipment  generates  uses  and  can 

radiate  radio  frequency  energy  and,  if  not  installed  and  used  in  accordance  with  the  instructions,  may  cause  harmful  interference  to  radio 

communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful 

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct 

the interference by one of the following measures: 

-  Reorient or relocate the receiving antenna. 

-  Increase the separation between the equipment and receiver. 

-  Connect the equipment into an outlet on a circuit different from that 

to which the receiver is connected. 

-  Consult the dealer or an experienced radio/TV technician for help. 

FCC  Caution:  Any  changes  or  modifications  not  expressly  approved  by  the  party  responsible  for  compliance  could  void  the  user's  authority  to 

operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device 

may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired 

operation. 

IMPORTANT NOTE: 

Radiation Exposure Statement: 

This  equipment  complies  with  FCC  radiation  exposure  limits  set  forth  for  an  uncontrolled  environment.  This  equipment  should  be  installed  and 

operated with minimum distance 20cm between the radiator & your body. 

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 

Country Code selection feature to be disabled for products marketed to the US/CANADA 

Industry Canada statement: 

This de i e  o plies  ith I dustry Ca ada’s li e e

-exempt RSSs. Operation is subject to the following two conditions:   

(1)

 

This  device  may  not  cause  interference;  and  (2)  This  device  must  accept  any  interference,  including  interference  that  may  cause  undesired 

operation of the device.   

(1)

 

Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada. Son fonctionnement est soumis aux deux conditions suivantes: (1) 

Ce dispositif ne peut causer d'interférences; et (2) Ce dispositif doit accepter toute interférence, y compris les interférences qui peuvent causer 

un mauvais fonctionnement de l'appareil. 

Radiation Exposure Statement: 

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and 

operated with minimum distance 20cm between the radiator & your body. 

Déclaration d'exposition aux radiations: 

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit 

être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. 

Summary of Contents for CPE7000









Reviews: