background image

 

                                           

       

Page 11 

 

 

  

9.

 

Limitation of Liability 

 

Gen3 believes the information contained in this publication is accurate, and reserves 
the  right  to  make  changes  in  specification  and  information  without  prior  notice. 
Gen3 is not responsible for any inadvertent errors. 

 

The  terms  and  conditions  governing  the  sale  of  Gen3  Systems  Limited  hardware 
products,  and  the  licensing  of  Gen3  Systems  Limited  Software,  consists  solely  of 
those  set  forth  in  the  written  contracts  between  Gen3  Systems  Limited  and  its 
customers.  No representation or affirmation of fact contained in this publication, 
including but not limited to statements regarding capacity, sensitivity, suitability of 
use, or performance of product described herein shall be deemed to be a warranty 
by Gen3 Systems Limited for any purpose or give rise to any liability by Gen3 Systems 
Limited whatsoever. 
 
In no event shall Gen3 Systems Limited be liable for any accidental, indirect, special, 
or  consequential  damages  whatsoever,  including  but  not  limited  to  lost  profits, 
arising out of or relating to this publication or the information contained in it, even 
if Gen3 Systems Limited, has been advised, or knew of, or should have known of the 
possibility of such damages.   

 
 
 

10.

 

Technical Assistance

 

 

If you encounter a problem, please review the system installation and operation. If 
the  problem  persists,  you  can  obtain  technical  support  from  your  local 
representative or from Gen3 direct: 

 

Gen3 
B2, Armstrong Mall, 
Southwood Business Park 
Farnborough, 
Hampshire, 
GU14 0NR 
United Kingdom 
 
Tel: +44 (0)1252 521500 
E-mail: techsupport@gen3systems.com 

 
Ensure that you have a full description of the problem, test conditions and operation 
sequence  available  before  you  call  for  assistance.    Remember  to  have  the  serial 
number of the system available before you contact us. 

Summary of Contents for Gensonic













Reviews: