background image

 

 S

AVE THESE INSTRUCTIONS – This manual is in addition to the Owner's Manual for the generator. All 

warnings and recommendations in the manufacturer's manuals must be strictly adhered to for safe use.

 

 

1

READ THIS MANUAL THOROUGHLY

If any portion of this manual is not understood, contact the near-

est Authorized Service Dealer for starting, operating and servicing 

procedures.
Throughout this publication, and on tags and decals affixed to the 

generator, DANGER, WARNING, CAUTION and NOTE blocks are 

used to alert personnel to special instructions about a particular 

service or operation that may be hazardous if performed incor-

rectly or carelessly. Observe them carefully. Their definitions are 

as follows:

INDICATES A HAZARDOUS SITUATION OR ACTION WHICH, IF 

NOT AVOIDED, WILL RESULT IN DEATH OR SERIOUS INJURY.

Indicates a hazardous situation or action which, if not 

avoided, could result in death or serious injury.

Indicates a hazardous situation or action which, if not 

avoided, could result in minor or moderate injury.

NOTE:

Notes contain additional information important to a procedure 

and will be found within the regular text body of this manual.

These safety warnings cannot eliminate the hazards that they 

indicate. Common sense and strict compliance with the special 

instructions while performing the action or service are essential to 

preventing accidents.
Four commonly used safety symbols accompany the 

DANGER

WARNING

 and 

CAUTION

 blocks. The type of information each 

indicates is as follows:

 This symbol points out important safety information that, 

if not followed, could endanger personal safety and/or 

property of others.

This symbol points out potential explosion hazard.

This symbol points out potential fire hazard.

This symbol points out potential electrical shock hazard.

SAFETY RULES

Study these SAFETY RULES carefully before installing, operating or 

servicing this equipment. Become familiar with this 

Owner’s Manual

 

and with the unit. The generator can operate safely, efficiently and 

reliably only if it is properly installed, operated and maintained. 

Many accidents are caused by failing to follow simple and funda-

mental rules or precautions.
The manufacturer cannot anticipate every possible circumstance 

that might involve a hazard. The warnings in this manual, and on 

tags and decals affixed to the unit are, therefore, not all-inclusive. If 

using a procedure, work method or operating technique the manu-

facturer does not specifically recommend, ensure that it is safe for 

others. Also make sure the procedure, work method or operating 

technique utilized does not render the generator unsafe.

 

 Despite the safe design of this unit, operating 

this equipment imprudently, neglecting its mainte-

nance or being careless can cause possible inju-

ry or death. Permit only responsible and capable 

persons to operate or maintain this equipment.

 

 Potentially lethal voltages are generated by 

these machines. Ensure all steps are taken to 

render the machine safe before attempting to 

work on the generator.

 

 Parts of the generator are rotating and/or hot 

during operation. Exercise care near running 

generators. 

 

 S

AVE THESE INSTRUCTIONS – The manufacturer suggests that these rules for safe operation be copied and 

posted in potential hazard areas. Safety should be stressed to all operators, potential operators, and service 

and repair technicians for this equipment.

 

 S

AVE THESE INSTRUCTIONS – This manual contains important instructions that should be followed during 

installation and maintenance of the generator and batteries.

Safety Rules

CALIFORNIA PROPOSITION 65 WARNING

Engine exhaust and some of its constituents are known 

to the State of California to cause cancer, birth defects 

and other reproductive harm.

CALIFORNIA PROPOSITION 65 WARNING

This product contains or emits chemicals known to the 

State of California to cause cancer, birth defects and 

other reproductive harm.

Summary of Contents for NEXUS Remote Monitor













Reviews: