background image

Generac Portable Products PP5000T Generator

6

BEFORE STARTING ENGINE

Add Oil

WARNING!

Any attempt to crank or start the

engine before it has been properly filled with the

recommended oil may result in an engine

failure.

To fill your engine with oil:

• Place generator on a level surface.
• Clean area around oil fill and remove oil fill cap.
• Select the oil's viscosity grade and fill engine with oil

following the instructions given in the engine owner’s

manual. 

Do Not overfill!

• Install oil fill cap.

NOTE:

The generator’s revolving field rides on a pre-

lubricated and sealed ball bearing that requires no

additional lubrication for the life of the bearing.

Add Gasoline

DANGER! 

Explosion Hazard! 

Never

fill fuel

tank indoors. 

Never

fill fuel tank when engine is

running or hot. 

Do Not

light a cigarette or smoke

when filling the fuel tank.

WARNING!

Do Not

overfill the fuel tank.

Always allow room for fuel expansion.

• Use regular 

UNLEADED

gasoline with the

Generator engine. 

Do Not

use premium gasoline.

Do Not

mix oil with gasoline.

• Clean area around fuel fill cap, remove cap.
• Add unleaded regular gasoline, slowly to fuel tank.

Be careful not to overfill. Allow about 1/2" of tank

space for fuel expansion (Figure 3).

• Install fuel cap and wipe up any spilled gasoline.

IMPORTANT:

It is important to prevent gum deposits

from forming in essential fuel system parts such as the

carburetor, fuel filter, fuel hose or tank during storage.

Also, experience indicates that alcohol-blended fuels

(called gasohol, ethanol or methanol) can attract

moisture which leads to separation and formation of

acids during storage. Acidic gas can damage the fuel

system of an engine while in storage.
To avoid engine problems, the fuel system should be

emptied before storage of 30 days or longer. See

“Storage” on page 11. 

Never

use engine or carburetor

cleaner products in the fuel tank or permanent

damage may occur.

Figure 3 — Fill Tank with Fuel

Summary of Contents for PP5000T





















Reviews: