background image

English

26.  Air compressors get hot while in operation. 

NEVER touch the motor, discharge tubing or 
compressor pump while in operation. 

27.  The Compressor operates automatically while the 

motor is turned on.

28.  Compressed air from the unit may contain carbon 

monoxide. Air produced is not suitable for breathing 
purposes.

29.  Always use a respirator when spraying paint or 

chemicals.

30.  The air pressure switch is set at the factory for 

optimum performance of your equipment. Never 
attempt to bypass or remove this switch as serious 
damage to equipment or personal injury could result 
from excessive air pressure.

KNOw YOUr COMPreSSOr

Handle: 

Convenient, rubber gripped handle allows 

for easy transport of your air compressor.

Air Regulator: 

The air regulator controls the air 

flow pressure. Turn regulator clockwise to increase 
air pressure, counter-clockwise to decrease air 
pressure.

Air Chuck:

 Convenient quick disconnect air chuck 

allows for fast easy connection to an air hose.

Tank Drain Valve:

 The Tank Drain Valve can be 

opened to allow moisture and compressed air to be 
released from the Air Tank.

Air Filter:

 This heavy duty metal air filter keeps 

your compressor running cleanly, by filtering out 
impurities.

Oil Breather Cap:

 As the compressor motor 

operates pressurized air must be released from the 
crank case. The oil breather cap allows built up air 
to escape, while shielding your air compressor from 
airborne impurities.

Power Switch:

 The red tipped power switch turns 

the air compressor on and off. 

Note:

  Always make sure that compressor Power 

Switch is in the OFF position before 
performing any maintenance or plugging the 
compressor into a power supply.

Pressure Gauges:

 These dual gauges indicate the 

amount of air pressure built up in the air tank, as 
well as the air pressure being delivered to the air 
chuck.

Safety Valve:

 The Safety Valve device relieves 

pressure from the Air Tank in the event of excessive 
pressure build up. The Safety Valve is preset at 
factory. Do not attempt to make any adjustments to 
the Safety Valve. Periodically pull ring on the Safety 
Valve end to check that it is working properly.

Air Tank:

 Powder coated steel tank stores the 

compressed air until it is needed.

3

!

!

wArNiNG

Tank Drain Valve should always be opened  

slowly to avoid damage to equipment and 

possible injury.

Air
Chuck

Handle

Air 
Regulator

Tank Drain Valve

(not visible in photo)

Air
Filter

Oil
Breather
Cap

Power 

Switch

Pressure

Gauges

Safety

Valve

Air Tank

Summary of Contents for AC1102

















Reviews: