background image

 

 

TL104

4.0  Test Lamp Maintenance and Warranty 

4.1 Maintenance 

Routine maintenance for the test lamp is minimal. When the battery can no longer hold the 
requisite charge after a 14-hour recharge, the battery must be recycled. General Monitors has a 
recycle program in place to recycle the used lead-acid battery. 

• 

When the test lamp is not being used, it is important to ensure that the test lamp is 
docked on the charger and the charger is connected to a live 120 VAC power cord.  

• 

Make sure that the test lamp lens is free of frost or large accumulations of moisture 
during frosty conditions or inclement weather. 

4.2 Warranty 

General Monitors warrants the TL104 Test Lamp and the accessory battery charger to be free 
from defects in workmanship or material under normal use and service within two (2) years 
from the date of shipment.  

General Monitors will repair or replace without charge any equipment found to be defective 
during the warranty period. Full determination of the nature of, and responsibility for, defective 
or damaged equipment will be made by General Monitors’ personnel.  

Defective or damaged equipment must be shipped prepaid to General Monitors or the 
representative from which shipment was made. In all cases, this warranty is limited to the cost 
of the equipment supplied by General Monitors. The customer will assume all liability for the 
misuse of this equipment by its employees or other personnel.  

All warranties are contingent upon proper use in the application for which the product was 
intended and do not cover products which have been modified or repaired without General 
Monitors’ approval or which have been subjected to neglect, accident, improper installation or 
application, or on which the original identification marks have been removed or altered.  

Except for the express warranty stated above, General Monitors disclaims all warranties with 
regard to the products sold, including all implied warranties of merchantability and fitness and 
the express warranties stated herein are in lieu of all obligations or liabilities on the part of 
General Monitors for damages including, but not limited to, consequential damages arising out 
of / or in connection with the use or performance of the product. 

Summary of Contents for TL104














Reviews: