background image

 

 

 

WARNING!    Read  and  understand  all  instructions. 

Failure to follow all instructions listed below may result in 

electric  shock,  fire  and/or  serious  personal  injury.       
Replacement manuals are available upon request at no 
charge,  or  may  be  downloaded  from  our  website, 

www.drainbrain.com

.  Instructional  videos  are  available 

for download on our website, and may be ordered.  If you 
have  any  questions  or  problems,  please  call  General’s 
customer service department at 412-771-6300. 

 

SAVE THESE INSTRUCTIONS!

 

SAFETY SYMBOLS 

Jet-Set JM-1000™  

Electric  shock  resulting  in  death  can 

occur if you plug this machine into an 
improperly wired outlet.  If the ground 

wire is electrified, you can be electro-

cuted  by  just  touching  the  machine, 

even when the power switch is off.  

ground  fault  circuit  interrupter  will  not 

protect  you  in  this  situation.  Use  a  UL 
approved tester to determine if the outlet 

is safe.  

Do  not  operate  power  tools  in  explo-

sive  atmospheres,  such  as  in  the 
presence of flammable liquids, gases, 

or dust.

 Power tools create sparks which 

may ignite the dust of fumes. 

 

Do  not  spray  flammable  liquids.

  Risk 

of explosion. Flammable liquids can cre-
ate fumes which can ignite causing prop-

erty damage or severe injury. 

 

Always  wear  safety  glasses  and  rub-
ber soled, non-slip shoes. 

High pres-

sure  spray  can  cause  paint  chips  or 

other  particles  to  become  airborne 
and  fly  at  high  speeds. 

Use  of  this 

safety  equipment  may  prevent  serious 
injury. 

These instructions are intended to  

familiarize all personnel with the safe operation 

and maintenance procedures for the JM-1000. 

 

DANGER indicates a hazard with a high level of risk which, if not 
avoided, will result in death or serious injury. 

CAUTION indicates a hazard with a low level of risk which, if not 
avoided, will result in minor or moderate injury. 

 

This is the safety alert symbol. It is used 

to  alert  you  to  potential  personal  injury 

hazards.  Obey  all  safety  messages  that 

follow  this  symbol  to  avoid  possible    

injury or death.

 

WARNING indicates a hazard with a medium level of risk which, if 
not avoided, could result in death or serious injury. 

Do not direct discharge stream at peo-

ple. 

 This equipment can produce a high 

pressure  stream  of  fluid  that  can  pierce 

skin and its underlying tissues, leading to 

serious injury and possible amputation or 

death. 

WARNING 

This  product  can  expose  you  to  chemicals  including  lead, 

which is known to the State of California to cause cancer and 
birth defects or other reproductive harm. For more information 

go to 

www.P65Warnings.ca.gov

 

Summary of Contents for Mini-Jet JM-1000-A









Reviews: