background image

 

Table of Contents  

IMPORTANT SAFETY INSTRUCTIONS ................................................................................... 2  
Table of Contents ................................................................................................................  3  
Electrical Requirements ......................................................................................................  4  
Specifications ......................................................................................................................  5  
For Your Own Safety ...........................................................................................................  5  
Contents of Shipping Carton ...............................................................................................  6  
Tools Required for Assembly ..............................................................................................  6  
Assembly ............................................................................................................................  7 
Operating Instructions ........................................................................................................  10  
Changing Bag/Filters ....................................................................................................... 

11  

Recommended Accessories ................................................................................................  12 

Warranty and Service ……………………………………………………………………………………………………. 

 13 

Parts Breakdown for the 1 1/2 HP Dust Collector with and without Canister ...................  14  
1 1/2 HP Dust Collector Parts List 

……….

.............................................................................  15 

 
 

 

Summary of Contents for 10-105

















Reviews: