background image

UNPACKING AND SET-UP

UNPACKING

Carefully unpack and remove the unit and its components from its shipping container and check for missing or
damaged items as per the list of contents below.

NOTE: Please report any damaged or missing items to your GENERAL® INTERNATIONAL distributor immediately.

LIST OF CONTENTS

Separate and verify that all parts are in your accessories
hardware bags.

QTY

MACHINE  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
RED STOP COVER   . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
DUST HOSE ADAPTOR 2” TO 4”  . . . . . . . . . . . . . . . . . .1
SANDING SPINDLE HARDWARE
—  Sanding drum spindle assembly 1 1/2”  . . . . . .1
—  Sanding drum spindle assembly 2”  . . . . . . . . .1
—  Sanding sleeve 5/8” . . . . . . . . . . . . . . . . . . . . . . .1
—  Sanding sleeve 1/2” . . . . . . . . . . . . . . . . . . . . . . .1
—  Sanding sleeve 1/4” . . . . . . . . . . . . . . . . . . . . . . .1
—  Spindle 5/8” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
—  Spindle 1/2” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
—  Spindle 1/4” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
TABLE INSERT 2”(oblong)  . . . . . . . . . . . . . . . . . . . . . .1
TABLE INSERT 3/4” (oblong)  . . . . . . . . . . . . . . . . . . . .1
TABLE INSERT 3/4”(round -*

Mounted on the machine

)  . . . . .1

TABLE INSERT 2” (round)  . . . . . . . . . . . . . . . . . . . . . . .1

10-12 mm WRENCH  . . . . . . . . . . . . . . . . . . . . . . . . . . .1
14-17 mm WRENCH  . . . . . . . . . . . . . . . . . . . . . . . . . . .2

6

SET UP SAFETY

ADDITIONAL REQUIREMENTS FOR SET UP

• Machinists square 
• Medium Phillips Screwdriver
• An extra person for help lifting

Serious personal injury could occur if you con-
nect the machine to the power source before
you have completed the set up process. DO NOT
connect the machine to the power source until
instructed to do so.

The MODEL 15-220M1 is a heavy machine 
(81 lbs shipping weight–37kg). Do not over-
exert. Arrange to have help nearby and ready
for unpacking and set up.

Summary of Contents for 15-220



















Reviews: