background image

 

 

ver 1.0 

 

5

5

5

5    

absolute fidelity

 

1

 

A Quick Start Set-up Guide 

Now that you have your new Genesis 7.1 Convertible (G7.1c), we 
realize that you can’t wait to hook it up and start playing! However, 
please read this quick set-up guide (even if your dealer is setting it up for 
you) before you proceed. 

1.1

 

Unpacking 

Your loudspeakers will come to you in two shipping cartons weighing 
over 35lbs (16kgs) each. Care must be taken when moving the carton 
around, and taking the speaker out of the box. While the speaker is 
small, it is also slippery and heavy. Use correct lifting techniques utilizing 
the muscles in your legs, and not just your back. 

We will 

not

 be held liable for damage to either the speakers or your 

backs during unpacking and setting up. Be careful as you may 
inadvertently damage the drivers if the cabinet slips and you grab at it 
and put a finger into the woofers. Do not try to lift the cabinet by the 
shield (it is not a handle!) or by grabbing the woofers as handles. 

1.2

 

Placement 

As a stereo pair of speakers, a good starting position for your G7.1c 
is at least 18 inches (45cm) into the room as measured from the front 
wall (the wall you look at as you are seated listening to the speakers) to 
the back of the speakers. Place the speakers vertically on a stand that is 
at least 18 inches high, and about five feet (1.5 metres) apart with the 
tweeters closest together. Toe the speakers in very slightly towards the 
listeners – by about 3 to 10 degrees – no more. 

Used as a center channel, the G7.1c can be placed below or above 
your screen. If you have a perforated, sonically transparent projector 
screen, you may place it behind the screen. In all cases, do not point 
the tweeter directly at the ears of the listeners. Angle the speaker so 
that the tweeter points 12 inches (30cm) below the ears or over the 
top of the head. 

You will want to sit nine to twelve feet (three to four metres) away from 
the speakers. When sitting further away, you should place the speakers 
further apart. When sitting nearer the speakers, move the speakers 
closer together. 

If you are using the G7.1c as surround or rear speakers, and you are 
hanging them on the wall, you will need a qualified installer to mount 
them on very strong brackets. The speakers weigh over 30 pounds 

Summary of Contents for G7.1c


















Reviews: