background image

 

 

SY-SIX-KLCS | Synergis IX Touch Sense LCD Keypad | Installation Manual 
Last Updated July 2018 

19

 

FCC Compliance Statements 

FCC PART 15, WARNINGS: INFORMATION TO USER 

This equipment complies with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and 
used in accordance with the instructions, may cause harmful interference to radio communications. However, 
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be deter-mined by turning the equipment off 
and on, the user is encouraged to try to correct the interference by one or more of the following measures: 

 

Re-orient the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

 

Changes or modifications not authorized by the party responsible for compliance could void the user's 
authority to operate this product. 

This device complies with Part 15 of the FCC rules. 

Operation is subject to the following two conditions: 

 

This device may not cause harmful interference.   

 

This device must accept any interference received, including interference that may cause undesired 
operation. 

 

NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT 
EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS 
COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. 

 

Summary of Contents for Synergis IX SY-SIX-KLCS






















Reviews: