SECTION 2 - OPERATION
Function settings are designed to make installatio n an d programmi ng
convenient and fast . Simpl y activat e a Functi on d
ip swi tch to get the opti on
you want.
Please refer to
Appendix 2
, th e
DM X Chann el Contr ol Diagram
,
fo
r a mo re
detailed explanation of effect positions.
When using a DMX c ontroller, c hannels
correlate with scanner functions. So
when you move a slider on the color channel, for example, the colors will
TM
change. Shiva-150R/200R/250R scanner effect channels follow:
Channel Control Positions
DMX512 Control
Dimming
Strobe and
Shutter:
Channel 1 Channel 2
Colors
Channel 3
Gobos
Channel 4
Gobo
Rotation
Channel 5
Pan
Channel 6
Tilt
Function Settings
Function Dip Switch Diagram
#1 Off
Transitions between colors
and gobos are visible.
#1 On
Transitions between colors or gobos
are covered by the shutter.
#2 Off
Color wheel stops at any
position; Single colors or
adjacent two-color
combinations are possible.
#3 Off
Exterior control mode. For use
with any DMX controller.
6
5
4
3
2
1
N
O
7
6
5
4
3
2
1
N
O
8
8
6
5
4
3
2
1
N
O
7
6
5
4
3
2
1
N
O
8
8
6
5
4
3
2
1
N
O
7
6
5
4
3
2
1
N
O
8
8
6
5
4
3
2
1
N
O
7
6
5
4
3
2
1
N
O
8
8
6
5
4
3
2
1
N
O
7
6
5
4
3
2
1
N
O
8
8
6
5
4
3
2
1
N
O
7
6
5
4
3
2
1
N
O
8
8
Color wheel stops only at full color
positions. Only single colors are
possible.
Built-in slow motion program is activated.
#3 On
6
9
3. Disconnect DMX512
cab le. Turn on Fu
nct ion d ip sw
itch #4,
activating the self-tes t function. I f scanne r operate s properly , th e DM X
signal cable or connector is likely at fault. Replace the DMX cable.
2. Check DMX512 dip switc h setting s. Ma ke su re the u n it is addres sed
properly. Make sure that Function dip switches 1-5 and 7 are off.
5. If lamp is not discolored or cracked, reinsert it. Close the lamp holder ,
tightening two screws (B6) securely. Connect power.
6. If lamp doesn't light, refer servicing to a qualified technician.
Problem: Lamp light is not visible but fan is turning.
Solution:
4. Disconnect power. Le t un it coo l. Chec k lam p. If la m p is crac ke d or
discolored, rather than clear, replace it. S ee
L
amp I nstallation
a nd
L
amp
Removal
sections for details.
Trouble-shooting
The
following trouble-shooting guide i
s provided to
hel
p produc tuser
s solv
e
minor problems. Always refer servicing to a qualified technician.
Problem: Lamp is not lit and fan is not turning. (Fan can be seen through the
back panel.)
Solution:
1. Check electric main s fo r prop er pow er connecti on. Ch eck tha t the
power supply matches product power supply specifications.
2. Check the fuse. First , disconnec t main s powe r suppl y. Us e a flat-hea d
screwdriver to pry open the fuse holder casing (B4) near the IEC socket
(B5). If t he f use i s d iscolored, r ather t han c lear, r eplace it . A re placement
fuse is provided in the fuse holder (B4). Always use appropriate type of
fuse. (See
Product Specifications
.)
1. Adjust your DMX controller sliders to open the scanner shutter channel,
channel 1. Refer to
Appendix 2
and controller instruction manual if
necessary.
Proper DMX512 addresses must be set on each scanner. Appendix 1
is a Chart of standard addressing for the six-channel Shiva-
TM
150R/200R/250R scanner. Refer to the guide DMX512 Basics for
more information.
