background image

Gen

i

us Gate Systems Ltd

4 Wayside Green Woodcote Reading Berks RG8 0QJ

Mail@Genius-Systems.co.uk

Directors: D.M.Pearson. M.J.Thornton. J.A.Pearson

Registration No: 4557960 (England)

V.A.T.No: 815 9757 88

Page 1

Setup Instructions of the DMG1 6/6 Telecommander

Genius Gate

Systems Ltd

DMG1    6/6

www.Genius-Systems.co,.uk

SIM

CARD

Aerial Lead

Connector Strip

DIP Switch

Power input

SIM Card

Status indicator

Before attempting to set up the unit you will need the following:

1. A suitable weather proof cabinet to install the complete system. The DMG is NOT suitable for

outside installation.

2. A SIM card for any of the GSM networks.

The SIM may be on any Tariff. But it is best to check the billing is per second not per minute

as few calls will extend to a minute in normal use.

3. A suitable Power supply of nominal Voltage 12 Volts DC (11 to 14 Volts) terminating in a

2.1mm female plug with the centre contact being Positive. It should be externally fused at 2

A although the mean current is about 350mA. The negative line must be grounded and/or

connected to the ‘Common’ line for all of the other equipment

4. A GSM Dual band Antenna with a Female FME connector. This can either be directly

connected to the flying antenna lead or via an extension lead and adaptors as needed.

Note: We can advise on or supply any of the above items if desired.

Set Up – Basic with default settings

The default setting will give no call forward and call duration when answered of around 30

seconds. The call duration timer is restarted each time the remote party presses a button to

operate a relay (whether the relay is in use or not by the gate control equipment). This will allow

the call to be extended indefinitely.

The DMG Telecommander is a simple

remote control device based on GSM

Cellular technology that provides

interfaces for a standard push button gate

access unit with voice capability that will

connect to any fixed line or mobile

telephone over the public network. There

are options for toll free inbound calling

and SMS communications.

It provides up to 6 dry contact relay

outputs (one of which is a toggle) that

may be commanded from the keypad on

the remote telephone handset.

Its important features are as shown

opposite

Summary of Contents for DMG1 6/6 Telecommander






Reviews: