OPEN A
STOP
FSW
SET UP
OPEN A
OPEN B
RADIO SET UP
ENGLISH
11 PROGRAMMING
11.1 Setting the board
Set the unit with Dip�Swit�h DS� to o�tain the operation you
require�
11.2 Learning
During the learning procedure, the obstacle detection device
does not operate. However, the STOP command and the
closing safety devices (FSW) are enabled; if they are triggered,
learning is interrupted and a fault is signalled.
The SETUP �y�le is �arrie� out with the plasti� housin�
installe�� Just re�o�e the rear �oor (Fi�� �8)�
Grip the rear �oor with �oth han�s an� pull �ently
�ownwar�� When you ha�e �inishe� the pro�e�ure
�es�ri�e� in this �hapter� put the �oor �a�k in pla�e�
The learnin� �y�le �akes it possi�le to �e�ine the �ollowin�:
� the �or�e require� to �o�e the �oor�
� the slow��own points�
� the openin� an� �losin� stop points�
� the pause ti�e (in auto�ati� lo�i�)�
Learnin� �ust �e starte� with the operator lo�ke�� irrespe�ti�e
o� the �oor’s position�
The pro�e�ure also �eter�ines the operatin� lo�i��
The lo�i� ta�les in�i�ate the �eha�iour o� the auto�ate�
syste� in �i��erent �on�itions� an� �ollowin� �o��an�s or
a�tion �y the sa�ety �e�i�es�
Learnin� �an �e auto�ati� or �anual� In the latter �ase� the
openin� an� �losin� �e�eleration points �an �e �eter�ine��
Howe�er� in auto�ati� �o�e� the unit in�epen�ently �eter�ines
the �o�e�ent para�eters�
I� the pro�e�ure is not �orre�tly �on�lu�e� (e��� �ue to e��essi�e
�ri�tion �urin� �oor �o�e�ent)� the unit si�nals a �ault status
(the SET UP LED �lashes slowly)� In this �ase� the pro�e�ure �ust
�e repeate� a�ter the �ause is eli�inate��
AUTOMATIC LEARNING WITH LOGIC �E�� (SEMI-AUTOMATIC)
Press the SET UP push��utton �or one se�on��
The SET UP LED starts to �lash when you release the
push��utton�
�) A�ter 8 se�on�s the operator auto�ati�ally �loses the �oor
until the stop point is �ete�te��
�) The operator �e�ins the openin� �o�e�ent� Wait until the
stop point is rea�he�� or �i�e an OPEN �o��an� in the
position where you wish to stop �otion�
��) The operator �loses the �oor�
�) Wait �or the �oor to rea�h the stop point an� �or the
operator to stop�
I� the learnin� pro�e�ure ter�inate� positi�ely� the SET UP LED
stops �lashin� an� stays li�hte� �or �� se�on�s�
Fig. 29
Fig. 2�
Radio signal programming push-button OPEN B.
RADIO SET UP LED signalling that the OPEN B radio signal is stored in the memory.
Radio signal programming push-button OPEN A.
RADIO SET UP LED signalling that the OPEN A radio signal is stored in the memory.
LED signalling the SET UP stage.
LED signalling photocells status.
LED signalling STOP.
LED signalling OPEN A.
OPEN push-button to totally open sectional door.
SET UP push-button for programming operating logics and learning work times.
www.otwieramy.com
