Genvex Optima 300 DESIGN User Manual Download

Page: 2 / 24

Optima 300

Table of contents

Page

1. Control panel

...........................................................

2. Installation

................................................................

2.1 Installation of the control panel ................................4

2.2 Mounting ..................................................................4

3. Start-up

.....................................................................

4. Operating

..................................................................

4.1 Operating and changing data in the

operating menu........................................................6

4.2 Daily operating options ............................................7

4.3 Main menu ...............................................................8

4.4 Schedule for week program...................................16

4.5 Schedule for defrosting..........................................16

4.6 Schedule for set-points ..........................................17

5. Function

.................................................................

5.1 Controlling Optima 300 ..........................................18

5.2 Extra capacity ........................................................18

5.3 Reliability ...............................................................18

6. Connection to PC

..................................................

6.1 Function description of data logger .......................19

6.2 Direct data logging.................................................21

7. Maintenance

...........................................................

7.1 Unit ........................................................................22

7.2 Alarms....................................................................22

7.3 Dismantling/decommissioning the device..............22

8. Troubleshooting

....................................................

8.1 High-pressure switch .............................................23

8.2 The device is not running ..................................... 23

8.3 Error on air side .....................................................23

Technical changes may have occurred after

publication of this document

Summary of Contents for Optima 300 DESIGN

























Search results

Summary of Contents for Optima 300 DESIGN

Reviews:

Related manuals for Optima 300 DESIGN

Brands by name

Popular brands

Genvex Optima 300 DESIGN, User Manual

Search results

Summary of Contents for Optima 300 DESIGN

Reviews:

Related manuals for Optima 300 DESIGN

Brands by name

Popular brands