background image

4

  

 

Optima 300

2. Installation

2.1 Installation of the control panel

The control panel is intended for hanging on a wall. The 

control panel must be positioned in the home at a height 

of about 1.5 metres from the floor. The control panel must 

not be countersunk into the wall, since the panel also 

functions as a room thermostat. It is also equipped with 

a light sensor. The control panel must not be exposed to 

direct sunlight. It must not be mounted on an outer wall or 

the room sensor will not be able to measure the correct 

room temperature and the light sensor will not regulate 

the light in the display correctly. It is also recommended 

that you do not place a lamp underneath the control panel 

as this may also affect the light sensor. 

2.2 Mounting

Find the place where the control panel is to be mounted, 

mark the places for the holes and screw the fitting onto 

the wall. 

Hold the wall frame against the wall and mark the holes 

for mounting the frame. Drilling of holes, the size of the 

holes and the corresponding screws for mounting will all 

depend on the wall material. 

Place the control panel down into the fittings and tip it in 

against the wall. 

At the bottom of the control panel there is access to: 

A: Terminal board. Connection to main circuit board 

B: SD card 

C: Room sensor 

D: Light sensor 

E: USB port 

Fit a low-voltage cable 4 x 0.25 mm² between the unit 

and the control panel. The maximum cable length is 

50 m. The voltage drop will be too great if the cable 

is over 50 m long and this may produce operational 

disturbances. 

The wall fixture can be mounted in two ways: 

Screw the fixture on to a smooth wall and lead the 

1. 

cable up from below so that it is visible. 

Fit a masonry junction box or a countersunk box to 

2. 

e.g. a plaster wall. If another type of box is preferred, 

to must be ensured that the screw hole match. 

Connect the low-voltage cable to the terminal box. Check 

that the cable is connected to the same numbers at both 

ends. (Between the control panel and the main circuit 

board in the unit) 

Clip the control panel onto the wall fixture by moving 

it downwards a little bit out at the bottom and finish by 

pressing it in at the bottom so that it is flush with the wall. 

To dismantle, pull the control panel out slightly at the 

bottom and lift it up.

Pos.

Amount

Product no.

Description

1

1

069014

House for panel

2

1

069015

Front for panel

3

1

069016

Plate for display

4

1

069012

Wall fittings

5

1

069017

Glas for display

Summary of Contents for Optima 300 DESIGN

























Reviews: