circuit that is completely protected against overloads, short circuits and thermal faults. Output is rated at 100 watts
into 4 ohms, with excellent overload recovery characteristics. A unique feature of this amplifi er is the “on silicon”
temperature sensor that automatically tracks and adjusts the amplifi er’s operating and protection parameters, a very
cool feature the increases product reliability 10-fold over conventional designs.
FAN COOLING
– A rear mounted fan is provided for exceptional thermal cooling of the power amp. A fan switch
is provided to disengage the fan if desired. It is recommended, but not necessary, to use the fan when only
operating the Shen-100 combo. Using the fan is recommended when powering an 8 ohm extension cabinet with the
combo or when operating the combo in a hot environment.
TWEETER LEVEL CONTROL
– The “rocker switch” tweeter level control provides three positions for
additional acoustic fl exibility. The positions are: On, Off and –6db.
SPEAKER OUTPUT JACKS
– The Shenandoah™ Acoustic 100 provides 2 parallel ¼” speaker output jacks.
Minimum total load is 4 ohms (2 x 8 ohm speaker cabinet or 1 x 4 ohm speaker cabinet). Combo versions of the
Shenandoah™ Acoustic 100 are factory equipped with our GBE 1230, 12” speaker and a compression bullet tweeter
presenting an 8 ohm load to the amplifi er.
POWER INPUT
– The Shenandoah™ Acoustic 100 is shipped from the factory with a standard IEC type power
inlet connector and the appropriate power cable for the market the amplifi er was shipped to. The power transformer
is a universal input (115/230 volt, 50/60 Hz) with a voltage selector switch located above the inlet connector. Be sure
that this switch is in the correct position (matching your local power system) BEFORE connecting the Shenandoah to
the power source. There is an AC mains fuse (with a spare fuse included!) located in the small slide out tray on the
IEC power inlet connector. Always replace with the correct value fuse as indicated on the fuse chart located on the
back of the amplifi er.
BOTTOM MOUNTED TILT-BACK HANDLE
– This feature allows the cabinet to be tipped up towards the
performer. This also can change the tone of the amp and reduce boomy low frequencies.
SPEAKER STAND MOUNT
– A 1 1/2” speaker stand mount is provided for use with a speaker stand.
CAUTION!
•
Never set an amplifi er on anything that will tip over or collapse under its weight.
•
These amplifi ers are capable of producing sound pressure levels that may cause hearing loss.
•
There are no user serviceable parts inside these units. Always consult a qualifi ed repair facility for service.
WARNING!
•
The use and operation of this device constitutes an agreement of full release of any and all liability
connected with its use. Only persons familiar with the operation of high-powered audio equipment should
attempt to operate this device.
•
In addition, by use of this device, the user agrees to hold Genz Benz Enclosures, Inc. and it’s designers,
sales agents and all other affi liates and related parties harmless in the event of any accident, injury, damage
or loss resulting from such use.
•
Manufacturer’s sole responsibility is to provide a warranty on the specifi ed performance of the product under
normal operating conditions for a period of 3 years.
WARRANTY:
•
Genz Benz Enclosures, Inc. warrants the model Shenandoah™ Acoustic 100 to be free from defects in
materials and workmanship for a period of 3 years from the date of purchase, when purchased from an
authorized Genz Benz dealer.
•
This warranty does not cover normal wear and tear incurred from the normally designed use of the product.
•
This warranty is effective only if a copy of the original sales receipt is presented at the time of warranty
service
•
This limited warranty is completely transferable to any subsequent buyer as long as the original sales receipt
is also transferred to such subsequent buyer.
•
All warranty service must be performed by a Genz Benz authorized service center.
•
Before returning any unit for service, a returned merchandise authorization number (RMA#) must be
obtained by calling 480-941-0705.
4
