Battery Status
Specifications
Working Radius
(Laser dependent):
1 m - 450 m
Operator’s Manual
FR 66-MM
Laser Detection Height:
127 mm
Numeric Readout Height:
102 mm
Accuracy (Dead band):
Ultra Fine
0.5 mm
Super Fine
1.0 mm
Full -
Batteries
OK
Half -
Initial
Warning
Outline -
Approx.
30 Minutes
Remaining
Flashing -
Change
Batteries
Fine
2.0 mm
Medium
5.0 mm
Move clamp position
Coarse
10 mm
Calibration:
0.1 mm
Reception Angle:
± 45° minimum
Detectable Spectrum:
610 nm - 780 nm
Beeper Volumes:
Loud = 110 dBA
Medium = 95 dBA
Low = 65 dBA
Center on-grade clamp position –
clamp position is sensed automatically
and displayed. Standard center
position displays an equal amount of
information above and below grade.
With no clamp, center on-grade.
LED Grade Indicators:
Front
Green on-grade
Red Hi
Blue Low
Power Supply:
2 x 1.5V AA
Battery Life:
60+ hours
Automatic Shut Off:
30 Min.,24 h, OFF
Environmental:
IP67
Weight without clamp:
371 g
Dimensions without clamp:
168 x 76 x 36 mm
Operating Temperature:
-20°C - +60°C
Storage Temperature:
-40°C - +70°C
Offset on-grade clamp position –
clamp position is sensed automatically
and displayed. Offset clamp position
moves the on-grade location to allow
more grade information to be
displayed above grade. This is useful
in applications where going below
grade is not required, i.e. driving
stakes down to grade.
*Specifications subject to change without notice.
Rod Clamp
Warranty
Front view
Rear view
1.
Keypad - Power, Accuracy, Units & Volume switches.
9.
Battery Door & Latch for two “AA” batteries.
2.
LED-Display - Green for on-grade & Red for high / low
10.
Marking Notch (80 mm from top).
3.
Beeper output - Fast, solid & slow audible signal.
11.
Captive Screw Thread, Center on-grade clamp position.
4.
Bubble Vial - aids in keeping FR 66-MM level.
12.
Captive Screw Thread, Offset on-grade clamp position.
5.
Anti-strobe sensor - Reduces false indication from
13.
Clamp Guides - Dimples align rod clamp.
This product is warranted by the manufacturer to the original
purchaser to be free from defects in material and workmanship
under normal use for a period of two (2) years from the date of
purchase. During the warranty period, and upon proof of
purchase, the product will be repaired or replaced (with the
same or similar model at manufacturers option), without charge
for either parts or labour. In case of a defect please contact the
dealer where you originally purchased this product. The
warranty will not apply to this product if it has been misused,
abused or altered. Without limiting the foregoing, leakage of the
battery, bending or dropping the unit are presumed to be
defects resulting from misuse or abuse.
strobe lights.
14.
Serial Number / ID Label.
6.
SuperCell Reception Window - 127 mm of height.
15.
Rear LCD - repeats indications of front LCD.
1.
Captive Rod Clamp Screw - attaches to the back of detector.
Specifications subject to change without notice.
7.
Front LCD - Displays elevation, settings and status.
16.
Rubber over mold - Protects the unit from drops.
2.
Alignment Points (2) - help secure and align rod clamp.
8.
On-grade Mark - Aligned with laser center on-grade
3.
Clamping Screw Knob - secures clamp to rods by moving the
reading. (80 mm from top)
traveling jaw. Clockwise tightens; Counterclockwise loosens.
4.
Reference Bar - top of bar is aligned with on-grade.
5.
Traveling Jaw - moving jaw grips tightly to rods.
Installing the Batteries
6.
Reversible Face - slanted face for round and oval rods;
1.
Open the battery door using a coin or similar
flat face for rectangular and square rods.
pry device to release the battery door tab.
Contact
2.
Insert two AA batteries noting the
geo-FENNEL GmbH
plus (+) and minus (-)
Kupferstraße 6
diagrams inside the battery housing.
D-34225 Baunatal
Tel. +49 561 49 21 45
3.
Close the battery door. Push down until
Fax +49 561 49 72 34
it “clicks” into the locked position.
Email: info@geo-fennel.de
www.geo-fennel.de
geo-FENNEL – Precision by tradition
