Action
Display
Remarks
Action
Display
Remarks
Turn power ON/OFF
CAPTURE Function
Initialization:
A) Receiver is in the laser beam and
The current elevation
Press any switch to return to normal
1. Test of LCD, LED and beeper
the power is on
reading will be held.
operation.
2. CAL: Calibration (3 sec.)
A flashing display will
3. Unit is ready for use.
confirm the reading
has been captured.
(Do not power up the unit in a laser beam
or strobe. If detected, the unit will display
“E200” and revert to the previous
Press and hold for 2 seconds to turn
calibration.)
power OFF.
B) Receiver is out of the laser beam
A short intermittent
Select accuracy
and power is on:
beep (The beeper
The selected unit of measure determines
will turn on to
the displayed deadband (accuracy).
Low if turned off.)
The current accuracy is stored in memory
and will be retained when the unit is
turned off or when batteries are replaced.
Press once to change current setting
2. Place the receiver in the beam.
The beeper will chirp
Press any switch to return to normal
(A beep confirms the selected volume.)
(Example: Fasten it to a measuring
rapidly after
operation.
rod, bring the receiver into the
approximately 5 seconds
Select beeper volume
laser beam. You now have 5
seconds
to confirm beam capture.
The current beeper
to plumb the rod and get the
A flashing display will
volume is stored in
reading captured.)
also indicate the reading
memory and will be
has been captured.
retained when the
unit is turned off
Special Menu Functions
or when batteries
Change special Menu Functions only
(No symbol)
Beeper
OFF
are replaced.
in the case of
special job requirements!
Press once to display current setting;
SENS
Sensitivity Medium*-HighLow
push again to scroll through options.
AVG
Averaging algorithm Medium*High - Low
Sensitivity of reception
D.R.O.
Numeric display ON*-OFF
SENS (Sensitivity):
Select units of measure
UNIT
Units of measure MM*-CM-IN-FRAC-FT
Selects reception sensitivity to laser and
The current unit of measure is stored in
FRC.R.
Fractional Reduction ON*-OFF
other light sources.
memory and will be retained when the
ARRW
Arrow Display DB*(deadband)-PR (prop.)
MD - Medium*: for most applications.
unit is turned off or when batteries
O.O.B.
Out-of-Beam Display ON*-OFF
HI - High: When laser beam is
are replaced.
1. Scrolling up or down.
GRD.A.
Grade Alarm ON-OFF*
weak, or at very long distances.
A.S.O.
Automatic shutoff 0.5h*-24h-OFF
LO - Low: If outside sources are
TX.O.L.
Transmitter Out-of-Level OFF*RPS
disturbing elevation readings.
2. Enter Change mode.
TX.O.B
Transmitter Low Battery OFF*-RPS
Grade Alarm
INFO
Information about the Receiver
GRD.A. (Grade Alarm):
Press once to display current setting,
When turned ON, disables the audible
additional pushes to scroll through options.
3. Change selected items.
Automatic Shutoff
signal when on-grade. When moved out
A.S.O. (Automatic Shut Off):
of the on-grade deadband, the beeper
Select brightness of LEDs
0.5 - After 30 Minutes*
activates as normal:
The current
4. Confirm change.
OF - Off (Unit is permanently on.)
ON - Alarm on (Solid beeper OFF)
brightness of LEDs
24 - 24 hour shutoff.
OF - Alarm off (Solid beeper ON)*
is stored in memory
5. To Exit.
(No symbol)
and will be retained
Out-of-Beam Display
LEDs OFF
when the unit is
O.O.B. (Out-of-Beam Display):
* Default setting
turned off or when
Sequence to show direction to get back in
batteries are
the laser beam ( for 25 s)
For more information about special
replaced.
ON - Out-of-Beam Display ON*
Menu Function contact the manu-
Press together to cycle the selection.
OF - Out-of-Beam Display OFF
facturer, importer or your local dealer.
