background image

5

Normal Operation

Normal Operating Mode

The normal operating mode of 
the press will display the current 
actual Temperature at the top of 
the screen and the time setting 
or elapsed time below the 
temperature. 

The right side the screen will 
indicate the heating status by 
stating HEATING, READY, both 
of those words, or none at all, 
depending on if it is cooling down or heating up to the set temperature. 
READY is shown only if the current temperature is within 5 degrees of 
the set point temperature. 

The right side of the screen will also indicate the timing status by stating 
OPEN, TIMING or DONE. The DONE indicator may remain on in 
some cases until the press is opened back up.

If the pressure feature is enabled, the pressure bar graph will show the 
last known pressure exerted when the press was closed.

Setting Temperature

From the normal operating mode, 
simply press the TEMP key to set the 
temperature.

The  flashing 3-digit number is the 
temperature setting (not the actual 
current temp). Use the Arrow Keys to 
set the desired temperature. Hold them 
down to increase rapidly, press both 
together to set it to 350°F.

Press TEMP again to lock in the setting.

Summary of Contents for Digital Knight DK16


























Reviews: