background image

User Manual - P series

21

www.georgin.com

4. 

Breaking capacity (resistive circuits)

4.1.  Breaking capacities

Contact No.  

AC

DC

4/44

10A

240V

0.5A

110V

6/8/18/20/34/38/54

5A

240V

0.5A

130V

10/16/30/36/50/56

2A

240V

1A

130V

96/106/116/98/108/118

2.5A 

240V

1A

130V

92/102/112 

4A

115V

0.3A

110V

62/62C/162/162C/172/172C

5A

240V

0.4A

250V

60/60C/160/160C/170/170C 

7A

240V

0.25A

250V 6V

4D/44D/46D/ 6D/34D/54D

-

-

1mA / 100mA

4V / 30V

8D/10D/30D/38D/50D/16D/36D/56D

-

-

10mA / 100mA

6V / 24V

18D/20D

-

-

10mA / 100mA

6V / 24V

IMPORTANT

Intrinsic Safety certified instruments (Ex ia) are equipped with gold-plated contacts. These instruments must 

be interfaced via an Intrinsic Safety relay. Georgin recommends the RDN model - see fc-rdn-fren on  

www.georgin.com.

The explosion proof switches with cable output must be imperatively connected to an approved terminal 

block and a junction box.

4.2.  Breaking capacity limits

Gold-plated contacts

Minimum threshold

Maximum threshold

Never operate or test the 

instrument above the 

maximum threshold.

18D and 20D

10 mA - 6 Vdc

100 mA - 24 Vdc

6D, 34D, 54D, 4D, 44D and 46D

1 mA - 4 Vdc

100 mA - 30 Vdc

Other gold-plated contacts

10 mA - 6 Vdc

100 mA - 24 Vdc

Standard contacts: Never use below 100 mA - 24 VAC.

5.  The pneumatic switch

Labelling of the cell connections: 

NO operation

NC operation

U

A

E

Pression/Température

U

A

E

Pression/Température

For certain models, exhaust is via open cable gland or screw terminal (mandatory for ATEX models).

The control pressure applied to the unit affects the dead band at a given set point: the lower the supply 

pressure, the smaller the dead band, and vice-versa.

A : Power supply

E : Exhaust

U : Use

Summary of Contents for P Series

























Reviews: