background image

Safety Considerations

Warning:  Before performing service or maintenance 
operations on a system, turn off main power switches to the 
equipment.  Electrical shock could cause personal injury.

Installing and servicing heating and air conditioning equipment can 
be hazardous due to system pressure and electrical components.  
Only trained and qualified service personnel should install, repair 
or service heating and air conditioning equipment.  Untrained 
personnel can perform the basic maintenance functions of cleaning 
coils and cleaning and replacing filters.  All other operations should 
be performed by trained service personnel.  When working on 
heating and air conditioning equipment, observe precautions in 
the literature, tags and labels attached to the unit and other safety 
precautions that may apply.

Follow all safety codes.  Wear safety glasses and work gloves.  
Use a quenching cloth for brazing operations and have a fire 
extinguisher available.

Note:  Local codes and regulations take precedent over any 
recommendations by the manufacturer.  In addition to conforming to 
manufacturer’s and local municipal building codes, the equipment 
should also be installed in accordance with the National Electric 
Code and National Fire Protection Agency recommendations.

5

General Installation Information

Physical Data

ASTON SERIES AIR HANDLER INSTALLATION MANUAL

GAH022

GAH026

GAH030

GAH036

GAH042

GAH048

GAH060

Air Coil Total Face Area, ft2 [m2]

Tube outside diameter - in. [mm]

Number of rows

Fins per inch

Suction line connection - in. [mm] sweat

Liquid line connection - in. [mm] sweat

Nominal cooling capacity - tons [kW]

1.8 [6.44]

2.1 [7.59]

2.5 [8.79]

3 [10.55]

3.5 [12.30]

4 [14.06]

5 [17.58]

Condensate drain connection - (O.D.) in. [mm]

Blower Wheel Size (Dia x W), in. [mm]

Blower motor type/speeds

Blower motor output - hp [W]

Filter Standard - 1" [51mm] MERV3 disposable, in. [mm]

Electrical characteristics (60hz)

Shipping weight - lbs. [kg]

Operating weight - lbs. [kg]

4/28/14

GAH026

GAH036

GAH048

GAH060

Air Coil Total Face Area, ft2 [m2]

Tube outside diameter - in. [mm]

Number of rows

Fins per inch

Water In connection - in. [mm] sweat

Water Out connection - in. [mm] sweat

Nominal cooling capacity - tons [kW]

2.1 [7.59]

3 [10.55]

4 [14.06]

5 [17.58]

Condensate drain connection - (O.D) in. [mm]

Blower Wheel Size (Dia x W), in. [mm]

Blower motor type/speeds

Blower motor output - hp [W]

Filter Standard - 1" [51mm] MERV3 disposable, in. [mm]

Electrical characteristics (60hz)

Shipping weight - lbs. [kg]

Operating weight - lbs. [kg]

8/15/14

220 [99.79]

200 [90.71]

208/230 - 1ph

ECM variable speed

1/2 [373]

1 [746]

20 x 24 [508 x 635]

3/4 [19.05]

11  x 10 [279 x 254]

Air Handler Model Number (Hydronic)

Hydronic     

Coil

3

7/8 [22.22]

13

7/8 [22.22]

6.94 [0.64]

3/8 [9.52]

Air Handler Model Number (Refrigerant)

Evaporator 

Coil

5.83 [0.54]

3/8 [9.52]

2

3

12

5/8 [15.87]

7/8 [22.22]

3/8 [9.52]

Refrigerant

R-410a

3/4 [19.05]

11  x 10 [279 x 254]

ECM variable speed

1/2 [373]

1 [746]

20 x 24 [508 x 635]

208/230 - 1ph

215 [97.52]

220 [99.79]

195 [88.45]

200 [90.71]

Note:

 Water connection dimensions are O.D.

Summary of Contents for GAH022































Reviews: