17
9.
Operational Precautions
√
Use only 6mm Clamp Tool Holders with the UF-9700 handpiece. Do not use
4mm holders – they will damage the handpiece.
√
Ensure that the “CLAMP TOOL” selector switch is depressed when using
clamp tools of any kind.
√
For maximum efficiency, ensure all threaded and clamp tools and tool holders
are securely fastened. Loose connections will cause reduced power output.
√
Inspect tools, holders and handpiece screw threads for dirt and rust. All male
and female screw threads and all tool shoulders and interfaces must be kept
clean and true. Use acetone, wire scratch brush and cotton ear swabs to clean.
√
Use only Gesswein ordinary tools with the UF-9700 handpiece for maximum
efficiency. If custom clamp tools are used, please refer to the chart in 6.3 for
size recommendations.
√
Avoid touching tools mounted in the UF-9700 handpiece while they are
ultrasonically vibrating. They may be hot enough to cause burning.
√
Do not use highly viscous lubricants. Use Gesswein Stoning and Lubricating
Oil. Do not allow lubricants to enter the UF-9700 handpiece (as can occur
when the handpiece is held with the tool pointing upward). Lubricant oils can
penetrate into the handpiece and cause deterioration of components.
√
Protect the UF-9700 handpiece from sharp impact.
√
Protect the handpiece cable from impact, sharp objects and excessive heat.
Do not twist cable or bend sharply at the strain relief.
√
For operating comfort, use the earplugs provided.
√
When in use, make sure the power pack ventilation grills located on the rear
and bottom of the units are not covered or obstructed.
√
When not in use for extended periods, turn off the On/Off and Reset Switch.
Doing so will prevent your mounting a tool in the UF-9700 handpiece while the
unit is on.
√
Keep the power packs away from excessive heat, humidity and corrosive
chemicals.
√
Always disengage handpiece and power pack by the plugs — not the cords.
Note: Gesswein cannot accept responsibility for the incorrect use of ULTRAMAX DF/SF
power packs and/or UF-9700 ultrasonic handpiece.
4
3.
Specifications
Power Pack
Model
ULTRAMAX DF
ULTRAMAX SF
Electrical
115 or 230V, 50/60Hz
115 or 230V, 50/60Hz
Frequency (range)
24kHz (20.0-30.0kHz)
24KHz (20.0-30.0khz)
Amplitude (stroke)
4-40 microns
4-40 microns
Frequency Adjustment
Auto feedback system
Auto feedback system
Ultrasonic Power Output
45W maximum
45W maximum
Power Hand 2X Output
0-30V DC
N/A
Output Adjustment
(power and stroke)
Continuously variable
Continuously variable
Power Source
115V, 1 Ph, 50/60Hz
115V, 1 Ph, 50/60Hz
(230V available)
(230V available)
Power Consumption
200VA
100VA
Dimensions
6
3
⁄
8
"W x 11"D x 8
1
⁄
4
"H
7"W x 8
1
⁄
4
"D x 6"H
Net Wt.
8 lbs.
5 lbs.
Ultrasonic Handpiece
Model
UF-9700
Transducer
B.L.T. electrostrictive
Cable Length
2.0m (curl cord)
Screw Thread
M6; M4 with adapter
Dimensions
5"L x
9
⁄
16
" dia. tapered to
13
⁄
32
"
Net Wt.
4.5 oz.
Summary of Contents for Ultramax DF
Page 1: ...Instruction Manual for Models DF and SF 466 2...
Page 20: ......
