background image

3

Installation

Flusher disinfector S-406

9904

Safety rules

This machine is designed with a number of integrated safety devices. To avoid
personal injury it is essential that the safety devices are not bypassed or in any
other way put out of action.

General safety rules

• The machine should be connected in accordance with the installation

instructions.

• The machine may not by used by juveniles.

• Installation and servicing should be carried out by staff with experience of

this machine.

• The lid lock of the machine may not be bypassed under any circumstances.

• Leakage in the system, eg, due to worn lid gasket, must be repaired

immediately.

• Personnel concerned must study valid handbooks and service manuals prior to

any repairs or service work.

• The machine may not be sprayed with water.

• Caution must be observed when using corrosive detergents.

• Safety precautions must be observed when using hot water or steam.

Power cut-off device

The machine must always be provided with a separate power cut-off device in
the power supply line, easily accessible on the wall.

Caution symbols

This manual contains certain warnings, instructions and advice of such
importance that they are particularly emphasized. The configuration and use of
the appertaining symbols are as follows:

This symbol indicates a warning in text included in the manual.
Such warnings refer to hazards that can result in more or less
serious injury and in some cases fatal injury.

It is also used in warnings to avoid damage to the machine.

Summary of Contents for S-406

























Reviews: