background image

GfS – Gesellschaft für Sicherheitstechnik mbH

 · Tempowerkring 15 · 21079 Hamburg

Tel. +49 40 - 79 01 95 0 · Fax +49 40 - 79 01 95 11 · info@gfs-online.com · www.gfs-online.com

6

GfS

 

Safety at doors

7007xx_MA_GfS e-Bar_2014_SN1-99_GB

1.3.0  Functions of GfS e-Bar® 70073x, 70074x
 

Local alarm types

GfS e-Bar® activated

When activated the display of the cabled GfS e-Bar® is permanently illu-

minated green. Green is signaling that the door is alarm secured but 

might be opened at any time. In case of battery supply the GfS e-Bar® 

works in an energy saving mode without background illumination. The 

display shines for just about 15 sec. green and expires then.

Pre-alarm

While slightly pressing the GfS e-Bar® a red flashing light and an acoustic 

alarm (95dBA/1m) is emitted, which expires as soon as the GfS e-Bar® is 

released. The prealarm is activated just during the first mm of the pushing 

movement. The correct moment when the pre-alarm is turning into a main 

alarm can be adjusted by a regulating screw resp. in older versions of the 

GfS e-Bar® by a reed contact (see operating manual page 8). It would be 

ideal if the pre-alarm is set in a way that the main alarm is just activated 

when the GfS e-Bar® is pushed to a point in which the door is released. 

The pre-alarm can be transmitted to a central display 

Main alarm in case of an unauthorized or an emergency passage

When pressing the GfS e-Bar® completely the door is released. At the 

same time the display emits an intermittent green light and a permanent 

alarm with 95dBA. The acoustic and visual alarm can be just switched off 

on the integrated key switch. The main alarm can be transmitted to a cen-

tral display. With remote technology the main alarm is transmitted via 

channel 1.

Battery Control

When the GfS e-Bar® is battery supplied a gentle acoustic alarm in an in-

terval of 60 sec is emitted as soon as the voltage drops below 7 V. The 

display is not shining. The alarm is active till a new battery is connected.

Door-too-long-open-Alarm

Pre-condition for this feature is a reed-contact which is installed 

on the door and connected to the GfS e-Bar®. When the single re-

lease has been activated on the integrated key switch and the 

door stays open for more than 15 sec. a gentle “door-too-long-

open-alarm” is emitted in an interval of 3 sec. This alarm indicates 

that an authorized person has left the door open. As soon as the 

door is closed the alarm expires.

Summary of Contents for e-Bar 700 70 Series

































Reviews: