background image

 

 

Display Cases / Plug-in 

   

 

 

 

 

 

 

17 

www.ggmgastro.com 

 

The cabinet does not cool sufficiently 

 

The cabinet is in defrosting 
cycle  

 

Air inlet is blocked 

 

The products are not placed 
evenly on shelves 

 

The cabinet is installed in a 
wrong place (next to heat 
source or air ventilation) 

 

The cabinet is not levelled 

 

Evaporator frozen 

(Notice : This may affect fan 

rotation) 

 

Condenser fan does not work 

 

Wait for defrosting cycle to finish 

 

Free air inlet 

 

Place the goods in order 

 

Check the position of the cabinet 
in the store 

 

Level the cabinet 

 

Melt (thaw) the ice on evap 

 

Make sure fan is not working and 
then call technical service 

The engine is noisy 

 

Screws and bolts are loose 

 

The cabinet is not levelled 

 

Condenser is dirty 

 

Tighten screws and bolts 

 

Level the cabinet 

 

Clean the condenser 

Condensate problem occurs 

 

Poor ambient conditions (25C, 
%60) 

 

Poor air flow 

 

Doors left open for long time 
during product replenishment  

 

Check the position of the cabinet 
in the store 

 

Check the operation of fans and 
wiring 

 

Train the staff who use the cabinet 

Cabinet temperature is too much or too low 

 

Poor ambient conditions 

 

 

Evap are frozen 

 

Evap is obstructed 

 

The products are not placed 
evenly on shelves 

 

Digital thermometer’s SET 
parameters are 
wrong/changed 

 

Gas leakage from compressor 

 

Check the position of the cabinet 
in the store 

 

Check the suction line 

 

Needs cleaning 

 

Place the goods in order 

 

Call technical service. Technical 
person needs to adjust SET 
parameters again.  

 

Call technical service 

Water leaks and/or bad smell 

 

Drain line are obstructed or 
damaged 

 

Vaporization pan is not 
connected properly 

 

Water leakage from 
vaporization pan 

 

Clear the drain line 

 

Check and connect it correctly 

 

Check the heaters in operation 

Frosting and icing observed 

Inside the cabinet; 

 

Fans are not working 

On the evaporator; 

 

Probe deattached 

 

Air flow of cold air is 
destroyed 

 

Digital thermometer’s SET 
parameters are 
wrong/changed 

 

Check fan wiring  

 

Attach the probe back to its place  

 

Check the ventilation in store 

 

Call technical service. Technical 
person needs to adjust SET 

parameters again.  

 
 
 
 
 
 

*

GGM Gastro reserves the right to change any technical details and accessories without previous notice. 

Summary of Contents for REYHAN CL



















Reviews: