GGP ITALY SPA D 310, Operator'S Manual

15

STANDARDS OF USE

Insert the lower part (1) of the handle into the

respective holes, making sure that the hooks are fully
clicked into position.
Insert the lower right part (2) and lower left part (3) of the
handle into the respective holes of the handgrip, making
sure that the hooks are fully clicked into position.
Assembly the two sections of the handle using the knobs
(5) and the nuts and bolts supplied as shown. Attach the
cable clamp (6) to the position shown and then attach the
cable (7). 

The motor is controlled by a dual action switch to

prevent starting it accidentally.
To  start, press the button (2) and pull the lever (1). The
motor automatically stops when the lever (1) is released.

To  adjust the cutting height, tilt sideways the

machine and move the wheel axle into one of the three
slots, provided inside the chassis.
All the wheels must be at the same height. 
MAKE THIS ADJUSTMENT ONLY WHEN THE MOTOR
HAS STOPPED MOVING.

Connect the extension cable correctly as indicated.

Start the engine by pressing the safety push-button (2) and
pulling the switchgear lever (1).

While cutting, ensure that the electric cable is

3.3

3.1

3. GRASS CUTTING

2.2

2.1

2. DESCRIPTION OF CONTROLS

1.1

1. FINISH ASSEMBLY

EN

always behind you and on the area of grass already cut.
The lawn will look better if it is always cut to the same
height and in alternate directions.

When you have finishing mowing, release the lever

(1).
FIRST disconnect the cable extension from the supply
socket (2) and THEN from the side of the lawnmower’s
switchgear (3). 
WAIT FOR THE MOTOR TO STOP before carrying out any
type of work on the machine.

IMPORTANT – Regular, careful maintenance is essen-
tial for keeping the safety level and original perform-
ance of the machine unchanged in time.
Store the lawnmower in a dry place.

1) Wear strong working gloves during any cleaning, main-

tenance or adjustment operation on the machine.

2) Remove the grass debris after each cut and mud accu-

mulated inside the chassis to avoid their drying and thus
making the next start-up difficult.

3) Always ensure that ventilation openings are kept clear of

debris.

To replace a cutter, push it towards the center of the

rotor using pliers.
When fitting the new cutter, make sure it is fully hooked and
free of pivoting.

Do not use forced water and avoid wetting the

motor or the electrical components.
Do not use harsh products for cleaning the chassis.

Should you have any doubts or problems, do not hesitate
to contact your nearest Service Centre or your Dealer.

4.2

4.1

4. ROUTINE MAINTENANCE

3.4

The company  .........................................................................................

Certify that the lawnmower,walk behind with electric motor .................
Width of cut  ...........................................................................................
Motor.......................................................................................................
Tested by  ...............................................................................................
Conforms to the specifications of directives .........................................

Conformity assessment procedure followed ..........................................
Measured sound power level..................................................................
Guaranteed sound power level ..............................................................
Reference to harmonised standards ......................................................
Sound pressure level at the ear measured in compliance with 81/1051/EEC ...
Vibration level at the handle (EN 1033)...................................................

EC DECLARATION OF CONFORMITY

GGP ITALY SPA - Via del Lavoro,6 
31033 Castelfranco V.to (TV) ITALY
D 310
29 cm
SUMEC
SNCH, 11 route de Luxembourg - L-5230 SANDWEILER
98/37/EEC - 89/336/EEC ~ 93/68/EEC - 2000/14/EEC
73/23/EEC ~ 93/68/EEC
ANNEX VI
95 dB(A)
96 dB(A)
EN 60335-1:1994 - EN 786 - EN 292-2 - EN 1033
83 dB(A)
3 m/s2

Castelfranco Veneto (TV) - ITALY 10-10-2007 P. Tosato (Managing Director)