background image

13 

 

18 - WARRANTY 

All our products are supplied with a guarantee for materials and manufacturing failures for a period of maximum 12 
months from the date of the delivery. 
 

The guarantee is extended as it follows: 

In case of malfunction of the machinery contact the manufacturer and quote the trouble, the model, serial 
number and the operating conditions of the machine. At the receipt of the machine and after an accurate 
analysis,  the  manufacturer  reserves  the  right  to  repair  or  to  replace  the  product.  If  the  machine  is  still 
under guarantee, the manufacturer will repair or replace it free, but if the returned product is not defective, 
the  manufacturer  reserves  the  right  to  charge  the  freight  to  the  customer  (transport,  etc.).This  warranty 
must be considered annulled in case of damages caused by an incorrect use, negligence, wear and tear, 
chemical  corrosion,  installation  in  contrast  with  the  operating  instructions.  Any  eventual  modification  or 
different  use  of  the  machine  must  be  previously  authorized  by  the  manufacturer  through  a  written 
document, otherwise the manufacturer can be considered free even from the guarantee bond. The parts 
of the machine which are subjected to wear and tear are not included in the guarantee. All the items not 
explicitly  cited  or  damages  and  expenses  caused  by  the  defects  of  the  product  itself.  Implicitly  the 
customer accepts the conditions of the present warranty purchasing the machine. Eventual modifications 
to the guarantee must be authorized by the manufacturer through a written document. 

Summary of Contents for ADN 044














Reviews: