background image

E40.0.6x.6C-01 

Operating Manual EASY

LOG

 80BIN 

page 7 of 14 

 

 

Delete min-value 

Push button 

 for about 5 seconds. 

“CLr” is displayed and the min-values of all measuring 
channels are deleted. 

5.2  Operating possibilities at the device - logger operation 

Function 

Procedure 

Display and adjust 
cycle time 

Push button 

 and 

 at the same time. 

The main display shows “CYCL”. The secondary display 
shows the currently adjusted cycle time [in sec.]. 

If the logger is currently not recording, the desired cycle time 
[2 sec to 5h (18000 sec)] can be adjusted via the buttons 

 

 and 

 . 

Press button  

 again to confirm your adjustments and to 

leave the menu. 

Note:  

If no key is pressed for more than 2 min, the menu is 
quit without saving.  

Start recording 

Push button 

 for about 5 seconds. 

The main display shows “run”.  
The secondary display shows “no”
To start recording select “YES” with the arrow keys 
(button 

 or 

 ) and verify with 

 . 

Note: 

If no key is pressed for more than 2 min, the menu is 
quit without saving. 

Stop recording 

Push button 

 for about 5 seconds. 

The main display shows “HoLd”.  
The secondary display shows “no”
To stop recording select “YES” with the arrow key 
 (button 

 or 

 ) and verify with 

 . 

Note: 

If no key is pressed for more than 2 min, the menu is 
quit without saving. 

Notice: 

If you have activated one of the following options  
 

• “logger stop via buttons disabled”  

 

• “do not stop active logger”  

at the configuration of the logger the menu to 
stop the recording cannot be called. 

 

 

3

SET

1

2

2

3

SET

1

SET

1

2

3

SET

1

SET

1

2

3

SET

1

Summary of Contents for Greisinger EASYLOG 80BIN















Reviews: