60
T R O U B L E SHOOTING
TROUBLESHOOTING GUIDE
FOR HELPFUL VIDEOS VISIT:
GHOSTCONTROLS.COM/PAGES/INSTALLATION-VIDEO
FOR MORE TROUBLESHOOTING TIPS VISIT:
GHOSTCONTROLS.COM/PAGES/QUICK-TROUBLESHOOTING
LEARN NEW REMOTE
AUTOCLOSE
SETTING THE EXTENDED LIMIT (2nd is Applicable only if you have second arm)
LED INDICATORS-All LEDs Except Power Will Turn Off After 1 Minute of Inactivity
ALARM CODES
DO NOT USE this procedure if you already have a remote that operates the gate and just want to add an additional remote. If you
want to add an additional remote, please refer to the remote manual for adding additional remote for your system.
When enabled, gate will automatically close after the set time. This feature will only be active when gate is at the fully open position.
1. Press and hold the ‘LEARN XMTR’
until the alarm sounds and the yellow LED stays ON. Release the button.
2. Press and hold the desired remote button on the transmitter (within 10 seconds) until the alarm sounds or the gate is moving. The new
remote is now learned.
Enable and Set AutoClose Time:
1. Press and hold ‘SET AUTOCLOSE TIME’ push button
until the alarm sounds and the GREEN LED stays lit.
2. Release the button. The GREEN LED will start blinking at the rate of 1 blink per second.
3. Count the desired time for AUTOCLOSE (Range: 6 seconds to 60 minutes) using the GREEN LED.
4. Press and release the "SET AUTOCLOSE TIME" button again when the desired time is reached.
5. If AUTOCLOSE is enabled, the GREEN LED will remain ON.
Disable AutoClose:
1. Press and hold "SET AUTOCLOSE TIME" push button
until the alarm sounds and the GREEN LED stays On. Release the button.
2. Press the ‘SET AUTOCLOSE TIME’ button again within 5 seconds to disable AUTOCLOSE.
Setting the CLOSED Limit (PULL-TO-OPEN Installation):
1. Move the gate to the desired CLOSED position using the remote or the 1
st
Set/2
nd
SET JOG CLOSE or JOG OPEN buttons.
The JOG buttons can be used as ‘fine’ adjustment of the CLOSED limit.
2. Press and hold the 1
st
SET/ 2
nd
SET button until the alarm sounds, then release the button.
3. Press the remote to run the gate to the fully OPEN position. (Repeat Steps 1–3 only if you have a second arm.)
4. The unit will beep once to indicate that the new CLOSED limit is learned and stored. Verify the newly programmed closed limit by running the
gate from the OPEN limit to CLOSED limit.
Setting the OPEN Limit (PUSH-TO-OPEN Installation):
1. Move the gate to the desired OPEN position using the remote or the JOG CLOSE or JOG OPEN buttons.
The JOG button can be used as ‘fine’ adjustment of the CLOSED limit.
2. Press and hold the 1
st
SET/ 2
nd
SET button until the alarm sounds, then release the button.
3. Press the remote to run the gate to the fully CLOSED position. (Repeat Steps 1–3 only if you have a second arm.)
4. The unit will beep once to indicate that the new OPEN limit is learned and stored.
5. Verify the newly programmed open limit by running the gate from the CLOSED to OPEN limit.
= OFF
= ON
=BLINKING
= NO Input Power Present
= Transformer Power Present
= Solar Panel Power Present
POWER LED
(GREEN)
Battery Condition
1 Beep = GOOD Battery
4 Beeps = LOW Battery
= GOOD Battery
= LOW Battery
VacationMode
®
(Hold Closed)
2 Beeps = VacationMode
®
Enabled
3 Beeps = VacationMode
®
Disabled
Cycling Control Box Power Switch will
Disable
PartyMode
®
& VacationMode
®
PartyMode
®
(Hold Open)
2 Beeps = PartyMode
®
Enabled
3 Beeps = PartyMode
®
Disabled
Arm Connection
5 Beeps = 1
st
Arm Disconnected
6 Beeps = 2
nd
Arm Disconnected
BATTERY CONDITION LED
(YELLOW)
= Blink Once=Input Change Detected
=(Blink more than once)= Blink along with alarm
to provide visual feedback of various codes
STATUS LED
(RED)
=1
>1
= No Transmitter Signal
= Learn Transmitter Mode
= Transmitter Signal Detected
XMTR LED (YELLOW)
= AUTOCLOSE Disabled
= AUTOCLOSE Enabled
= AUTOCLOSE Suspended
AUTOCLOSE LED (GREEN)
(Alarm Codes are only active for 1 minute after gate has stopped moving, except where required by safety standard)
2018-08
