Features
Statement
The product is warranted against defects in material and
workmanship while used in normal service for a period of 1
year from the date of sale to the original customer. The GEM
policy is one of continual development and improvement;
therefore GEM reserves the right to change specifications
without notice.
Warranty
Specifications
Unit: mm
DG-600H
Stand-alone Proximity Reader
35
.5
70
12
7.
5
1
2
3
4
5
6
7
8
9
0
*
#
Allow up to 600 proximity cards and PIN codes
RF Frequency: EM-400x 125 KHz
Tamper switch and alarm buzzer included
Fully Programmable via keypad and master code
Access mode selectable: card only card or PIN card+PIN
Support Wiegand 26/44-bit format auxiliary reader
Logical memory to prevent duplication
Invalid PIN Lock-out
Beeper sound
Non-Volatile Memory
Removable memory chip replacement
Operating Voltage: 9VDC to 16VDC
Current Draw: Average 50mA, Peak 100mA/12VDC
Transmitting Frequency: 125 KHz,
Memory Volume: 600 Proximity cards/tokens and PIN codes
Read Range: Up to 10 cm (Depending on local installation
conditions)
Keyboard: 12 digits keypad (0~9, *, #)
Input: Request-to-exit, door reed switch, auxiliary reader
Relay rating: 2A MAX/30VDC, 0.4A/120VAC
Invalid PIN Lock-out: The system will shut down for 60
seconds After the attempt to read the master or PIN cards
has faiiled for over 8 times. (No beeper signal when pressing
on the keypad)
Relocking timer:
Strike Time: 1~99 seconds (adjustable)
Strike mode: Access Timer or Latch
Alarm Function:
Door Held Open Alarm: 10~99
Door Forced Alarm
Panel Temper Alarm
Auxiliary Reader Format: Wiegand 44 or 26-bit only format
(adjustable), hexadecimal (Em 64-bit standard R/O or
compatible)
Case Material: ABS (UL94V0)
Color: Dark gray/ Beige White
Operating Temperature: -20~+70°C
A m b i e n t H u m i d i t y : 5 ~ 9 5 % r e l a t i v e h u m i d i t y ( n o n -
condensing)
Visual Signals:3 LED display with audible Indication
(Red/Yellow/Green)
EMC: Meet CE requirement
EMC: Meet CE requirement
DG-600H stand-alone Proximity Reader is ideal for
single-door access control. It may connects to another reader
and serve as a controller. DG-600H enables the beeper to go
off whenever the keypad is pressed. A tamper switch is used to
protect the reader from external damage by linking the relay to
the alarming system. This model communicates in Wiegand
protocol and has a set of 600 proximity cards set to 26~37-bit
or 26-bit. (For DG-600E, proximity cards are set to either 26 or
44 bit.) It takes the reader 0.5 seconds at most to read a
proximity card or 5-digit PIN code. The built-in non-volatile
memory preserves the PINs for as long as 10 years. Even
when the power fails, the stored PIN codes will not be washed
away.
Copyright © Gianni Industries, Inc. All rights reserved.
DM-CA-DG-600H Ver. E Published on 2010.12.20
GIANNI INDUSTRIES, INC.
No. 13, Zhongxing Rd., Tucheng Dist., New Taipei
City 236,Taiwan (R.O.C.)
Tel: 886-2 2267 7986 / Fax: 886-2 2267 9876
E-Mail: inquiry@gianni.com.tw
Website: gianni.tw
