2. Read new card (1 beep), then press 4-digit PIN 9999 (1 beep, Right Yellow
LED stay on).
3. Press # (1 beep) back to standby mode (Right Green LED stay on)
Enter the master code twice (1234 1234) to enter programming mode (1 long
beep, Right Yellow LED stay on).
The dual identification feature allows the reader to be programmed to grant access
with either Proximity Card only, Proximity Card or PIN, Proximity Card and PIN.
1. Enter programming mode
2. Press*0 (Right Yellow LED rapid flash)
3. Press 00 (1 beep,Right Yellow LED stay on) for Proximity Card Only
Press 01 (1 beep,Right Yellow LED stay on) for Proximity Card or PIN
Press 02 (1 beep,Right Yellow LED stay on) for Proximity Card + PIN
4. Press # (1 beep) back to standby mode (Right Green LED stay on)
The relay strike time determines the amount of time that the door remains
unlocked after a valid proximity card or PIN is entered.
1. Enter programming mode
2. Press *1 for Relay 1 (Right Yellow LED rapid flash)
Press *5 for Relay 2 (Right Yellow LED rapid flash)
3. Press 00~99 (1 beep,Right Yellow LED stay on)
4. Press # (1 beep) back to standby mode (Right Green LED stay on)
1. Enter programming mode
2. Press * 8 (Right Yellow LED rapid flash)
3. Press 88 (No LED , 1 long beep, right Yellow LED stay on)
4. Press # (1 beep) back to standby mode (Ridht Green LED stay on)
1. Enter programming mode
2. Enter *8 (Right Yellow LED rapid flash)
3. Enter 99 (Both left & rigth Yellow LEDs stay on, 1 beep) back to standby mode
(Right Green LED stay on)
a.1. Enter programming mode to select slot position 000~999 (Left Green LED
stay on, Right Yellow LED rapid flash to indicate the slot position is available)
b. 1. Enter programming mode to select slot position 000~999 (Left Red LED stay
on, Right Yellow LED rapid flash to indicate the slot position is unavailable)
2. Press * * (1 beep) to delete the data from the slot position (Left Green LED
stay on, Right Yellow LED rapid flash)
3. Press # , back to satndby mode
4. Repeat the steps of 7-a to add new cards.
a. 1. Enter programming mode
2. Press * 4 to select slot position 00~09 (Left Green LED stay on , Right Yellow
LED rapid flash to indicate the slot position is available)
3. Read new card (1 beep, Right Yellow LED flash)
4. Press # (1 Beep) back to programming mode (Right Yellow LED flash)
5. Press # (1 Beep) , back to satndby mode
b. 1. Enter programming mode
2. Press * 4 to select slot position 00~09 (Left Red LED stay on , Right Yellow
LED rapid flash to indicate the slot position is unavailable)
3. Press * * to delete the data from the slot position (1 beep, Left Green LED
stay on, Right Yellow LED rapid flash)
4. Press # , back to satndby mode
5. Repeat the steps of 8-a to add new cards.
1. Enter programming mode
2. Press * 3 (Right Yellow LED rapid flash)
3. Enter 4-digit master code twice e.g. 4567 4567 (1 beep, Right Yellow LED stay on)
4. Press # (1 beep) back to standby mode (Right Green LED stay on)
a. 1. Enter programming mode
2. Press * 7 (Left Green LED rapid flash, Right Yellow LED rapid flash to
indicate the slot position is available)
3. Read new card to set as Master Card (1 beep, Right Yellow LED stay on)
4. Press # (1 beep) back to standby mode (Right Green LED stay on)
b. 1. Enter programming mode
2. Press * 7 (Left Green LED stay on , Right Yellow LED rapid flash to indicate
the Master Card had been stored)
3. Press* * to delete the data (1 beep, Left Green LED rapid flash, Right Yellow LED
rapid flash)
4. Press # , back to satndby mode
5. Repeat the steps of 10-a to add new master card.
a. 1. Read master card once (1 beep, Right Yellow LED stay on)
2. Enter slot position 000~999 (Left Green LED stay on, Right Yellow LED rapid
flash to indicate the slot position is available)
3. Read new card (1 beep), then enter 4-digit PIN 9999 (1 beep, Right Yellow LED
stay on)
4. Press # (1 beep) back to standby mode (Right Green LED stay on)
b. 1. Read master card once (1 beep, Right Yellow LED stay on)
2. Enter slot position 000~999 (Left Red LED stay on, Right Yellow LED rapid
flash to indicate the slot position is unavailable)
3. Press * * to delete the data from the slot position (1 beep, Left Green LED
stay on, Right Yellow LED rapid flash)
4. Repeat the steps of 11-a to add new cards.
1. Enter programming mode
2. Press * 6 (Right Yellow LED rapid flash)
3. Press 01 ( 1 beep, Right Yellow LED stay on) - function OFF
Press 02 ( 1 beep, Right Yellow LED stay on) - function ON
4. Press # (1 beep) back to standby mode (Right Green LED stay on)
1. Enter programming mode
2. Press * 2 (Right Yellow LED rapid flash)
3. Press 01 (1 beep, Right Yellow LED stay on) - function OFF
Press 02 (1 beep, Right Yellow LED stay on) - function ON
4. Press # (1 beep) back to standby mode (Right Green LED stay on)
Note: Turning on doorbell alarm function on the second relay, relay
strike time is 1 second.
Turn off the power: press # continuously, and energize (1 beep), the master code
is reset to default value.
The master code consists of a four-digit number and is used to access
programming functions of the reader and cannot be used to gain access i.e. It
cannot be the same as other PINs. The default master code is set as 1234. Under
normal operation the keypad is used for entering PIN to gain access. In the
programming mode the keypad can be used to add/delete PINs, set relay strike
time and other operation functions.
15.
Add new cards to Relay 1
1. Enter programming mode, press *9 (Right Yellow LED flash)
2. Press 01 (1 beep, right Yellow LED flash)
3. Select slot position 000~999, press the number of cards (001~999) (1 beep,
right Yellow LED flash)
4. Read new cards (in serial order) (1 beep, right Yellow LED flash)
5. Press # (1 beep) back to standby mode (right Green LED stay on)
16. Change PIN to Relay 1
1. Enter programming mode, press *9 (right Yellow LED flash)
2. Press 02 (1 beep, right Yellow LED flash)
3. Press slot position 000~999
4. Press PIN code (1 beep, right Yellow LED flash)
5. Press # (1 beep) back to programming mode (right Yellow LED stay on)
6. Press # (1 beep) back to standby mode (right Green LED stay on)
17. Change the length of Master Code
1. Enter programming mode, press *9 (right Yellow LED flash)
2. Press 04 (1 beep, right Yellow flash)
3. Press the length of Master Code (4 ~ 6 digits) (beep…clear PINs and cards)
(1 beep)
4. back to programming mode (right Yellow LED stay on)
5. Press # (1 beep) back to standby mode (right Green LED stay on)
(After changing the length of Master Code, all PINs and cards will be cleared
too. If the length of Master Code is 4 digits, press 1234; if 5 digits, press 12345;
if 6 digits, press 123456.)
14.
Reset the Master Code to Default Value
13. Turn Doorbell Alarm Function ON/OFF
12. Turn Anti-Tamper Alarm Function ON/OFF
11. Add New Cards by Master Card
10. Add a New Master Card to Relay 1
9. Change Master Code
8. Add a Proximity Card and PIN to Relay 2
7. Add a Proximity Card and PIN to Relay 1
6. Reset Controller Parameter to Default Value
5. Clear Memory of All Proximity Cards and PINs
4. Set the Relay Strike Time
3. Set the Access Mode
2. Enter Programming Mode
1. Master Code
Copyright All Rights Reserved. P-MU-DG-160-800 Ver.B Publish: 2011.01.12
