background image

Manual No. 3100022 

 

1

 

preliminaries 

 

Congratulations! 

 

You have just purchased one of the finest pieces of outdoor power equipment on the market today.  If 
properly cared for, your new truck loader will provide years of dependable service.  Please read and follow 
this instruction manual carefully in order to get the most out of your new equipment. 
 
As you carefully uncrate your unit, you will find the following items: 

 

      1  Power Unit 

1

 

Discharge Stack &Elbow Assembly

 

1   12” x 6’ Metal Discharge Hose (standard units) 
1  18” x 8’ Intake Hose (standard units) 
1  Horizontal Hose Support Boom Member 
1  Parts Accessory Kit including:

 

1 – 18” Intake Nozzle 
4 – 18” Hose Clamps 
1 – Hose Support Boom Horizontal Member 
1 – 12” Squeeze Ring 
1 – Package of assembly hardware 
1 – Package containing operating manuals and warranty registration 

 

Each product leaves our factory in excellent condition; occasionally, however, some damage may occur 
during shipment.  If any such damage is found upon initial inspection, 

immediately

 notify the transport 

carrier who delivered your machine, as they are solely responsible for such damage, as well as any 
subsequent adjustments necessary.  
 

Before assembly, please take a moment and record your model number and serial number below for future 
reference (both numbers are located on the silver tag adhered to the engine side of the impeller housing 
assembly): 
 

Model number_______________________________ 
 
Serial number________________________________ 

 

Also be sure to promptly fill out and return the warranty registration enclosed in your manual packet. 

 
Your new loader requires very little assembly.  Simply follow the instructions contained within this manual 
to begin enjoying the benefits of your new unit. 

 

 

CALIFORNIA PROPOSITION 65 WARNING

 

 

Gasoline and Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects and 

other reproductive harm. 

 

As an owner of off-road gasoline or diesel engine equipment and/or as an employer, you also may have an obligation under the California 

Occupational Safety and Health Act or under Proposition 65 to warn persons exposed to gas and diesel engine exhaust and/or other 

Proposition 65 chemicals in and around your workplace.  See California Health and Safety Code section 25249.5, Title 22 of the California 

Code of Regulations at Section 1200 

er seq.,

 and Title 8 of the California Code of Regulations Section 5194. 

Not 

for  

Reproduction

Summary of Contents for 3800014

























Reviews: