background image

12/18   GP7132_GP7136.indd

GIANT INDUSTRIES, INC.

 900 N. Westwood Ave., Toledo, Ohio  43607              

Phone: (419)-531-4600  FAX (419)-531-6836, www.giantpumps.com

 

Copyright 2018 Giant Industries, Inc.

GIANT INDUSTRIES LIMITED WARRANTY

Giant Industries, Inc. pumps and accessories are warranted by the manufacturer to be free from 
defects in workmanship and material as follows:
 

1.  For portable pressure washers and self-serve car wash applications, the discharge  

 

 

manifolds will never fail, period. If they ever fail, we will replace them free of charge.  

 

 

Our other pump parts, used in portable pressure washers and in car wash applications,  

 

 

are warranted for five years from the date of shipment for all pumps used in NON- 

 

 

SALINE, clean water applications.

 

2.    One (1) year from the date of shipment for all other Giant industrial and consumer  

 

 pumps.

 

3.    Six (6) months from the date of shipment for all rebuilt pumps.

 

4.    Ninety (90) days from the date of shipment for all Giant accessories.

                   
This warranty is limited to repair or replacement of pumps and accessories of which  
the  manufacturer’s evaluation shows were defective at the time of shipment by the manufacturer.  
The following items are NOT covered or will void the warranty:
 

1.   Defects caused by negligence or fault of the buyer or third party.

 

2.    Normal wear and tear to standard wear parts.

 

3.   Use of repair parts other than those manufactured or authorized by Giant.

 

4.   Improper use of the product as a component part.

 

5.   Changes or modifications made by the customer or third party.

 

6.   The operation of pumps and or accessories exceeding the specifications set forth  

 

 

in the Operations Manuals provided by Giant Industries, Inc.

Liability under this warranty is on all non-wear parts and limited to the replacement or repair of those 
products returned freight prepaid to Giant Industries which are deemed to be defective due to work-
manship or failure of material.  A Returned Goods Authorization (R.G.A.) number and completed 
warranty evaluation form is required prior to the return to Giant Industries of all products under war-
ranty consideration.  Call (419)-531-4600 or fax (419)-531-6836 to obtain an R.G.A. number.

Repair or replacement of defective products as provided is the sole and exclusive remedy provided 
hereunder and the MANUFACTURER SHALL NOT BE LIABLE FOR FURTHER LOSS, DAMAGES, 
OR EXPENSES, INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES DIRECTLY OR 
INDIRECTLY ARISING FROM THE SALE OR USE OF THIS PRODUCT.

THE LIMITED WARRANTY SET FORTH HEREIN IS IN LIEU OF ALL OTHER WARRANTIES OR 
REPRESENTATION, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WAR-
RANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND ALL SUCH 
WARRANTIES ARE HEREBY DISCLAIMED AND EXCLUDED BY THE MANUFACTURER.  

Summary of Contents for GP7132













Reviews: