User’s Manual
GT-650 BIOS Setup 4 - 33
FLOPPY DISK CNTRLR ERROR OR NO CNTRLR PRESENT
Cannot find or initialize the floppy drive controller. Make sure the controller
is installed correctly and firmly. If there are no floppy drives installed, be
sure the Diskette Drive selection in Setup is set to NONE.
Invalid EISA Configuration
PLEASE RUN EISA CONFIGURATION UTILITY
The non-volatile memory containing EISA configuration information was
programmed incorrectly or has become corrupt. Re-run EISA configuration
utility to correctly program the memory.
NOTE: When this error appears, the system will boot in ISA mode, which
allows you to run the EISA Configuration Utility.
KEYBOARD ERROR OR NO KEYBOARD PRESENT
Cannot initialize the keyboard. Make sure the keyboard is attached correctly
and no keys are being pressed during the boot.
If you are purposely configuring the system without a keyboard, set the error
halt condition in Setup to HALT ON ALL, BUT KEYBOARD. This will
cause the BIOS to ignore the missing keyboard and continue the boot.
Memory Address Error at...
Indicates a memory address error at a specific location. You can use
this location along with the memory map for your system to find and
replace the bad memory chips.
Memory parity Error at...
Indicates a memory parity error at a specific location. You can use this
location along with the memory map for your system to find and replace the
bad memory chips.
MEMORY SIZE HAS CHANGED SINCE LAST BOOT
Memory has been added or removed since the last boot. In EISA mode use
Configuration Utility to reconfigure the memory configuration. In ISA mode
enter Setup and enter the new memory size in the memory fields.
Memory Verify Error at...
Indicates an error verifying a value already written to memory. Use the
location along with your system's memory map to locate the bad chip.
Summary of Contents for GT-650
