User’s Manual
GT-650 BIOS Setup 4 - 35
Slot Not Empty
Indicates that a slot designated as empty by the EISA Configuration Utility
actually contains a board.
NOTE: When this error appears, the system will boot in ISA mode, which
allows you to run the EISA Configuration Utility.
SYSTEM HALTED, (CTRL-ALT-DEL) TO REBOOT...
Indicates the present boot attempt has been aborted and the system must be
rebooted. Press and hold down the CTRL and ALT keys and press DEL.
Wrong Board in Slot
PLEASE RUN EISA CONFIGURATION UTILITY
The board ID does not match the ID stored in the EISA non-volatile memory.
NOTE: When this error appears, the system will boot in ISA mode, which
allows you to run the EISA Configuration Utility.
FLOPPY DISK (S) fail (80)
→
Unable to reset floppy subsystem.
FLOPPY DISK (S) fail (40)
→
Floppy Type dismatch.
Hard Disk(s) fail (80)
→
HDD reset failed
Hard Disk(s) fail (40)
→
HDD controller diagnostics failed.
Hard Disk(s) fail (20)
→
HDD initialization error.
Hard Disk(s) fail (10)
→
Unable to recalibrate fixed disk.
Hard Disk(s) fail (08)
→
Sector Verify failed.
Keyboard is locked out - Unlock the key.
BIOS detect the keyboard is locked. P17 of keyboard controller is pulled low.
Keyboard error or no keyboard present.
Cannot initialize the keyboard. Make sure the keyboard is attached correctly
and no keys are being pressed during the boot.
Summary of Contents for GT-650
