background image

Appendix

- 65 -

English

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PnP/PCI Configurations
PC Health Status
MB Intelligent Tweaker(M.I.T.)

ESC: Quit

F3: Change Language

F8: Dual BIOS/Q-Flash

F10: Save & Exit Setup

Time, Date, Hard Disk Type...

6. Press 

Del 

to enter BIOS menu after system reboots. When you are in BIOS menu, move to

Load Fail-Safe Defaults

 item and press 

Enter

 to load BIOS Fail-Safe Defaults. Normally the system

redetects all devices after BIOS has been upgraded. Therefore, we highly recommend reloading the
BIOS defaults after BIOS has been upgraded.

Select Language
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving

Load Fail-Safe Defaults (Y/N)? Y

Press 

on your keyboard to load defaults.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PnP/PCI Configurations
PC Health Status
MB Intelligent Tweaker(M.I.T.)

ESC: Quit

F3: Change Language

F8: Dual BIOS/Q-Flash

F10: Save & Exit Setup

Time, Date, Hard Disk Type...

7. Select 

Save & Exit Setup

 item to save the settings to CMOS and exit the BIOS menu.

System will reboot after you exit the BIOS menu. The procedure is completed.

Select Language
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving

Save to CMOS and EXIT (Y/N)? Y

Press 

on your keyboard to save and exit.

Part Two:
Updating BIOS with Q-Flash

TM

 Utility on Single-BIOS Motherboards.

This part guides users of single-BIOS motherboards how to update BIOS using the Q-Flash

TM 

utility.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PnP/PCI Configurations
PC Health Status
MB Intelligent Tweaker(M.I.T.)

Top Performance
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving

ESC: Quit

F3: Change Language

F8: Q-Flash

F10: Save & Exit Setup

Time, Date, Hard Disk Type...

Summary of Contents for GA-8I945GME

















































































Reviews: