background image

MDE-3801 TRIND™ Multi 1 Transmitter/Receiver in Dispenser Retrofit Kit • 10/99

Page 1

Introduction

Purpose of this Manual

This manual provides instruction for installing TRIND™ Multi 1 Retrofit Kits in The 
Advantage

®

 Series wide frame and narrow frame units with InfoScreen

®

, monochrome 

CRIND

®

, or single-line CRIND. 

The TRIND option allows customers to automatically authorize CRIND-equipped units using 
a hand-held transponder tag provided by a major oil company (MOC). Use this kit for one- or 
two-sided units.

Prerequisites

Before installing the TRIND kit, ensure that the existing CRIND has the Z-180 logic board 
T17764-XX, which is not provided in TRIND retrofit kit.

Important Notice

This equipment has been tested and found to comply with the limits for a Class A digital 
device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference when the equipment is operated in a commercial 
environment. This equipment generates, uses and can radiate radio frequency energy, and if 
not installed and used in accordance with the instruction manual, may cause harmful 
interference to radio communications. Operation of this equipment in a residential area is 
likely to cause harmful interference in which case the user will be required to correct the 
interference at his own expense. Changes or modifications not expressly approved by the 
manufacturer could void the user’s authority to operate this equipment.

Required Reading

Before installing the equipment, the installer must read, understand, and follow:

• this  manual
• NFPA 30A, The Automotive and Marine Service Station Code
• NFPA 70, The National Electric Code
• applicable federal, state and local codes and regulations

Failure to do so may adversely effect the safe use and operation of the equipment.
Note: This kit must be installed by a Gilbarco ASC (Authorized Service Contractor) to insure 

warranty.

Related Documents

MDE-2531

Pump & Dispenser Start-Up & Service Manual

MDE-2562

CRIND Service Manual

MDE-2628

Cash Acceptor Retrofit Assemblies for The Advantage Series with CRIND

MDE-2620

Graphics Panel Application for The Advantage Series

PT-1728 

The Advantage Series Illustrated Parts Manual

PT-1736 

CRIND Card Reader Illustrated Parts Manual

MDE-3801

TRIND™ MULTI 1

Transmitter/Receiver in Dispenser

Retrofit Kits C00012-001-XX

Installation

Summary of Contents for TRIND MULTI 1 C00012-001-NF-D



























Reviews: