GILLIG LOW FLOOR Service Manual Download

Page: 146 / 506

Suspension

RIDE HEIGHT ADJUSTMENT

The air suspension height control valves (also known as “leveling valves”) automatically control the air

pressure in the air springs to maintain the proper ride height. As the vehicle is loaded, the air springs will

compress slightly. The height control valve actuating arm will be moved up from the neutral position to

the fill position. This will allow air from the air tanks to flow into the air springs, increasing the pressure

in the springs, bringing the air spring back to the proper height. When the vehicle is unloaded, the air

springs will slightly increase in length and the height control valve actuating arm will be moved from the

neutral position to the exhaust position. This will exhaust some of the air in the air spring until enough

air has been exhausted to bring the air spring back to the proper height. The proper air spring height

is important to allow for proper suspension travel and to maintain the proper driveline angles. Out-of-

adjustment air spring heights can cause the bus to lean, not allow for full suspension travel leading to

bottoming or topping out of the suspension, or cause improper driveline angles leading to driveline life

or vibration problems. The height control valves do not “level” the bus. They only control the air spring

height.
The front suspension has one height control valve and the rear has two. The two rear suspension height

control valves keep the bus level to the road (controls leaning) while the single front valve only main-

tains the proper air spring height at the front suspension air springs.

To check and adjust the air spring height:

1. The air system must have at least 80 psi in the accessory air tank. Before adjusting the air spring

height, run the engine until the air gauge in the dash reads at least 110 psi or apply shop air until

the gauge reads at least 100 psi.

Never get underneath any part of the coach unless its weight is fully

supported by jack stands or blocks on the frame. Never put yourself in

a position where a change in air spring pressure could cause the coach to

crush or pinch you. The Low Floor bus has very little ground clearance

with the air springs exhausted!

2. Either work from a pit or install jacks or blocks under the frame at the front and rear of the bus.

Refer to the “Jacking” section of the General Information chapter for jacking points. Do not jack

the bus up; just install the jacks or blocks up to the frame to prevent the bus from dropping and

causing injury or damage when the height control valves are adjusted. If the air spring heights are

too large before adjusting, the bus may lower down onto the jacks/blocks under the frame. If this

happens, raise the bus and set the jacks/blocks lower so the bus frame will clear the jacks/blocks

when the springs are set correctly.

3. First check the rough adjustment of the front air springs (Figure 5-2). The front air spring height

should be 9". If the front air spring height is 8.5" to 9.5", go to Step 4 and set the rear suspension

air spring height. If not within this range, loosen the clamp holding the link end and push the

link up to raise the air spring height or down to lower the air spring height. Move the link very

slowly; there will be a delay between the time when the link is moved, to when the air spring

height will start to change. When the proper air spring height is reached, center the valve in the

neutral position and tighten the link end clamp. To hold the valve in the neutral position while

Summary of Contents for LOW FLOOR



























































































































































































































































































































































































































































































































Search results

Summary of Contents for LOW FLOOR

Reviews:

Related manuals for LOW FLOOR

Brands by name

Popular brands

GILLIG LOW FLOOR, Service Manual

Search results

Summary of Contents for LOW FLOOR

Reviews:

Related manuals for LOW FLOOR

Brands by name

Popular brands