GILLIG LOW FLOOR Service Manual Download

Page: 296 / 506

Brakes & Wheels

296

Balanced Inflation

Balanced inflation means that all the tires on an axle maintain the same air pressure. A difference in pres

sure between the front and rear tires may be permissible, within limits. There should not, however, be a

difference between the left and right tires on the same axle. A five psi under-inflation on a single front

tire can affect ease of steering; and can also create steering hazards. An under-inflated rear tire can affect

braking efficiency and balance. Balance tire pressures for ease of steering, comfort in riding, safety in

driving, minimum fuel consumption, and maximum tire life.

Pressure Loss

At periodic intervals, each tire should be checked for pressure loss with an accurate gauge before the

tires are brought to the correct pressure. The purpose of this check is to ascertain the exact pressure loss

in each tire. If, at the time the check is made, a definite pressure loss is discovered on any tire, an inspec

tion of the tire should be made to discover the cause of the loss and to correct the condition if possible.

This check will establish a danger signal in the condition of the tires. The pressure loss check should

always be made with the same gauge so the test will be consistent if there is any inaccuracy in the gauge.

Tire Inspection

• Nails, small stones, bits of metal, or glass imbedded in the tread should be removed. If loss of air

results, the tire should be removed from the wheel, inspected for internal damage, and a permanent

repair made from inside the tire.

• All tire valves and extensions should be in good condition and equipped with valve caps. Use high

temperature valve cores.

• A cut or snag which exposes cord body will allow water to seep through, which may damage the

exposed cords. Dirt, water, and other materials penetrating between the tread and cord create an

abrasive action which literally separates the cord from the tread. Repair or replace the tire.

• A small hole in the tire which has not broken enough cords to weaken the cord body will allow air,

moisture, and foreign materials to penetrate and cause separation, as in the above case. Sharp or

abrasive objects left in the tire work back and forth, damaging the cords, leading to separation, and

ultimately to failure or a blowout. Separations caused by damage may occur at a point other than

the point of puncture. Repair or replace the tire.

• Abrasions are caused by rubbing or gouging by vehicle parts or road hazards. The continued abrad-

ing is hazardous as it can cause the tire to fail. The damaged part must be repaired and the dam-

aged tire repaired or replaced

Summary of Contents for LOW FLOOR



























































































































































































































































































































































































































































































































Search results

Summary of Contents for LOW FLOOR

Reviews:

Related manuals for LOW FLOOR

Brands by name

Popular brands

GILLIG LOW FLOOR, Service Manual

Search results

Summary of Contents for LOW FLOOR

Reviews:

Related manuals for LOW FLOOR

Brands by name

Popular brands