GIRBAU SLI14, Installation And Operating Instructions Manual

18

Girbau, SA

113432-1

Electric Models Only

All electrically heated dryers must be connected to the electric
service shown on the dryer’s data label.  The connecting
wires must be properly sized to handle the rated current.

1/25/06

Warning (Gas Models Only)

Dryers built for use with a voltage between 200
and 240 must verify the input voltage during

installation.  If the nominal voltage is outside of the
medium tolerances shown on the diagram below, adjust
the autotransformer, located near the burner assembly.  To
adjust the autotransformer wiring, place the red wire on the
appropriate tap (HIGH, MED, LOW) of the autotransformer.
For additional wiring details, refer to the electrical diagram
located on the inside of the control panel.

Electrical Service Specifications
Gas and Steam Models Only

!

TERM

LINE VOLTAGE

50 Hz

60 Hz

HIGH

260
226

283
249

MED

239
208

260
230

LOW

217
189

236
208

ELECTRICAL SERVICE SPECIFICATIONS

  IMPORTANT:

  NOTES: A.

 B.
 
 
 C.

208 VAC AND 230/240 VAC ARE NOT THE SAME.  When ordering, specify exact voltage.

When fuses are used they must be dual element, time delay, current limiting, class RK1 or

RK5 ONLY.  Calculate/determine correct fuse value, by applying either local and/or National
Electrical Codes to listed appliance amp draw data.
Circuit breakers are thermal-magnetic (industrial) motor curve type ONLY.  For others,
calculate/verify correct breaker size according to appliance amp draw rating and type
of breaker used.
Circuit breakers for 3-phase (3ø) dryers must be 3-pole type.

SERVICE

VOLTAGE

PHASE

WIRE

SERVICE

APPROX. AMP DRAW

CIRCUIT

BREAKER

60 Hz

50 Hz

SLI9  Gas

120

1ø

2

8.9

—

15

200

1ø

2

7.7

7.8

15

208

1ø

2

7.6

—

15

220

1ø

2

—

7.4

15

230

1ø

2

—

7.3

15

240

1ø

2

7.2

—

15

SLI14  Gas

120

1ø

2

10.3

—

15

200

1ø

2

8.7

8.8

15

208

1ø

2

8.4

—

15

220

1ø

2

—

8.1

15

230

1ø

2

—

7.8

15

240

1ø

2

7.7

—

15

SLI23  Gas

120

1ø

2

15.6

—

20

200

1ø

2

10.5

—

20

208

1ø

2

10.5

—

20

220

1ø

2

10.0

—

20

240

1ø

2

9.7

—

20

220

1ø

2

—

10.7

20

230

1ø

2

—

10.8

20

SLI23  Steam

120

1ø

2

14.4

—

20

200

1ø

2

8.2

—

20

208

1ø

2

8.2

—

20

220

1ø

2

7.8

—

20

240

1ø

2

7.6

—

20

220

1ø

2

—

8.4

20

230

1ø

2

—

8.5

20

SLI34  Gas

120

1ø

2

15.6

—

20

200

1ø

2

10.5

—

20

208

1ø

2

10.5

—

20

220

1ø

2

10.0

—

20

240

1ø

2

9.7

—

20

220

1ø

2

—

10.7

20

230

1ø

2

—

10.8

20

SLI34  Steam

120

1ø

2

14.4

—

20

200

1ø

2

8.2

—

20

208

1ø

2

8.2

—

20

220

1ø

2

7.8

—

20

240

1ø

2

7.6

—

20

220

1ø

2

—

8.4

20

230

1ø

2

—

8.5

20

1/25/06

ELECTRICAL SERVICE SPECIFICATIONS

  IMPORTANT:

  NOTES: A.

 B.

 C.

208 VAC AND 230/240 VAC ARE NOT THE SAME.  When ordering, specify exact voltage.

When fuses are used they must be dual element, time delay, current limiting, class RK1 or RK5
ONLY.  Calculate/determine correct fuse value, by applying either local and/or National Electrical
Codes to listed appliance amp draw data.
Circuit breakers are thermal-magnetic (industrial) type ONLY.  For others, calculate/verify correct
breaker size according to appliance amp draw rating and type of breaker used.
Circuit breakers for 3-phase (3ø) dryers must be 3-pole type.

SERVICE

VOLTAGE

PHASE

WIRE

SERVICE

OVEN

kW

APPROX.

AMP DRAW

CIRCUIT

BREAKER

60 Hz

50 Hz

SLI9

200

1ø

2

5.6

32.7

32.7

45

208

1ø

2

4.1

24.2

—

35

208

1ø

2

6.1

34.0

—

45

240

1ø

2

5.4

27.1

—

35

240

1ø

2

8.1

38.4

—

50

208

3ø

3

6.5

22.7

—

30

240

3ø

3

7.5

22.6

—

30

230

1ø

2

5.0

—

26.4

35

230

1ø

2

7.4

—

36.8

50

380

3ø

4

6.8

—

15.0

20

400

3ø

4

7.5

—

15.5

20

416

3ø

4

8.1

—

15.8

20

SLI14

200

1ø

2

12.5

68.0

67.7

90

208

1ø

2

7.9

43.5

—

60

208

1ø

2

13.5

70.4

—

90

240

1ø

2

9.0

42.6

—

60

240

1ø

2

13.5

61.4

—

80

208

3ø

3

13.5

43.0

—

60

240

3ø

3

13.5

37.6

—

50

230

1ø

2

8.3

—

41.3

60

230

1ø

2

12.4

—

59.1

80

380

3ø

4

11.3

—

22.6

30

400

3ø

4

12.4

—

23.1

30

416

3ø

4

13.5

—

23.7

30

SLI23

200

1ø

2

14.8

82.1

—

110

208

1ø

2

16.0

85.1

—

110

220

1ø

2

13.4

68.8

—

90

240

1ø

2

16.0

74.2

—

100

208

3ø

3

16.0

52.6

—

70

220

3ø

3

13.4

43.0

—

60

240

3ø

3

16.0

46.0

—

60

380

3ø

4

13.4

28.0

—

40

220

1ø

2

13.4

—

69.4

90

230

1ø

2

14.7

—

72.3

100

220

3ø

3

13.4

—

43.6

60

230

3ø

3

14.7

—

45.3

60

380

3ø

4

13.4

—

28.6

40

400

3ø

4

14.8

—

29.8

40

416

3ø

4

16.0

—

30.7

40

SLI34

200

1ø

2

20.3

109.8

—

150

208

1ø

2

22.0

113.9

—

150

220

1ø

2

18.5

91.7

—

125

240

1ø

2

22.0

99.2

—

125

208

3ø

3

22.0

69.2

—

90

220

3ø

3

18.5

56.2

—

80

240

3ø

3

22.0

60.4

—

80

380

3ø

4

18.4

35.6

—

45

220

1ø

2

18.5

—

92.3

125

230

1ø

2

20.2

—

96.3

125

220

3ø

3

18.5

—

56.8

80

230

3ø

3

20.2

—

59.1

80

380

3ø

4

18.4

—

36.2

50

400

3ø

4

20.4

—

37.8

50

416

3ø

4

22.0

—

39.1

50