14
14
USER’S GUIDE | TOP LOADING SCALE | MODEL DSN
ES
FR
IT
ENG
nonstoply.
ACCUMULATION
In the weighing mode, after the machine’s stable, press the
for weight accumulation. The display screen first shows the accumulated times
and then the accumulating total weight. In the zero point, pressing the
can read the accumulating contents. During the display of accumu-
lating contents; you can clear the accumulated records by pressing .
ALARM PRESET
8QGHUWKHZHLJKLQJPRGHLILW·VQHFHVVDU\WRVHWWKHXSSHU ORZHUOLPLWWRDODUPDXWRPDWLFDOO\SUHVV
. The display shows upper information
“H1” and after it shows “0”00000g. Press
,
and to input the upper limit value, and for confirmation press the to enter the lower
limit set. After the weight display illustrates the lower limit set information “-Lo-”, it shows “0”00000g. Press
,
and to input the
lower limit set value and press
again for checking. (Note: the upper limit set value must be higher than the lower limit value).
:KHQWKHZHLJKWLVLQWKHUDQJHRIWKHSUHVHWXSSHUDQGORZHUOLPLWYDOXHWKHEX]]HUZLOOPDNHWKHDODUPRI´'LGLGLµQRWHZKHQWKHXSSHUDQG
lower limit value is zero , the preset alarm is invalid. Ex: suppose the preset upper limit value is 2200g (the same as the lower limit preset)
Press the “rightward” for three times and the display shows 00”0”000.
Press the “increase by degree” twice and the display shows 00”2”000.
Press the “rightward” once and the display shows 002”0”00.
Press the “increase by degree” twice and the display shows 002”2”00.
CALIBRATION
Turn on the scale by pressing and holding the
until the display shows “CAL”. In a few seconds will display the current calibration value such
as 0300”0”(30000g).Press
,
and to input the calibration value and press
to confirm. At this moment, the calibration value is
glittering, and put the corresponding weight. Load the weight and press when it is stable, the single-point calibrations is done. (Requirement:
WKHZHLJKWYDOXHRIWKHVLQJOHSRLQWFDOLEUDWLRQVKRXOGEHDERYHWKHRIWKHIXOOYDOXH
UNIT SELECTION
Press
to choose the desire unit such as g, kg, ct, dwt, oz, lb and so on. The set unit will be automatically stored when turning the machine
on next time.
BACKLIGHT OPERATION
1. Two backlight modes are available here:”No backlight”mode and”auto-backlight mode. The”No backlight”will never show the backlight under
any condition. The “auto-backlight”mode will light up the backlight when any key is pressed or when the weight on the scale is more than
G)LYHVHFRQGVODWHUWKHOLJKWZLOOH[WLQJXLVKDIWHUWKHZHLJKWFRPHVWRµµ
2. On weight mode, you will enter into the other backlight mode by keeping pressing Backlight Key [
]. After setting the mode, the scale will
automatically keep the backlight mode set previously when you turn the scale on again.
BATTERY
:KHQWKHXQGHUYROWDJHLQGLFDWRULVJOLWWHULQJLWVKRZVWKHLQVXIILFLHQWSRZHUDQG\RXQHHGWRUHFKDUJHLWLQWLPH&RQQHFWWRWKHSRZHUVXSSO\
to make the AC indicator light up. This stands for it’s charging now. The average charging time is 12 hours.
ELECTRIC QUANTITY INDICATION
:KHQWKHXQGHUYROWDJHJOLWWHUVLWVKRZVWKHLQVXIILFLHQWSRZHUDQGQHHGUHFKDUJLQJLQWLPH
2. If the display screen does not show or shows “Lo”,this means The battery is in the self-protection state, and you should charge it in time and
then you can use it.
6. MENU SET
Press and hold
to enter Menu set. The display firstly shows the set information and then the value. Press
to choose the desire value.
Press
for confirmation to enter the next set .the scale will automatically back to the original after finishing set.
