background image

Model # 7LIECH-BP-G: Page 3

IMPORTANT: Do NOT Return Dispenser To Store. 

If you have a question or problem, please contact 844-GLACIAL(452-2425) for assistance. 

SAFETY PRECAUTIONS ---Electrical Requirements

PRODUCT FEATURES

Congratulations! You have chosen an Advanced Technology State of the Art Water 

Cooler.

The refrigeration system on this cooler cools the cold water by internal evaporator of commer

-

cial design flat forms the ice around it. This feature is called an "Ice Bank". It allows for ice 
cold water and keeps the water temperature consistently cold, however a Longer time in 
forming the Ice Bank is required. Since ice is an insulator, the more ice is built up, the slower 
next layer is made.

WHEN UNIT IS PLUGGED IN FOR THE FIRST TIME WAIT FOR UP TO 6 HOURS FOR 

COLD WATER TEMPERATURES TO REACH THE COLDEST SETTINGS.

                      Electrical shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an  adapter.
Do not use an extension cord.
Failure to follow these instructions can result in 
death, fire, or electrical shock.

WARNING

A 120 volt, 60 Hz., AC only, 15 amp, fused electrical supply is required. A time-delay

 

fuse or 

circuit breaker is recommended. 

If codes permit and a separate ground wire is used, it is recommended that a qualified 
electrician determine that the ground path is adequate.

Check with a qualified electrician if you are not sure if the water cooler is properly grounded.

Summary of Contents for 7LIECH-BP-G


















Reviews: