English
28/100
English
29/100
Do not use this machine if fatigued, sick, if you have
had medicines, drugs or alcohol.
Do not use this machine at night, with fog or with
reduced visibility. You must be able to see and control
the working area.
Lack of sleep or fatigue can cause accidents and
damages.
Never leave the machine unattended.
Do not allow anybody to enter the working area. The
perimeter is no less than 15 metres and nobody
should enter this working area as it is a danger zone.
Clean the working area and remove any obstacles that
could cause accidents.
Always regulate the machine on a flat and stable
surface.
Do not use accessories on the machine except
those recommended by our company. Use of non
recommended accessories could cause severe damages
to the user, to the people close by and to the machine.
Avoid using the machine when the ground is humid.
Be particularly careful if using the machine after it has
rained as you might slip more easily.
It is mandatory to switch off the engine when
transporting the machine between working areas.
7.1. FIXING THE MACHINE AND GUIDANCE
Whilst working, always hold the scarifier with both
hands. Always be behind the scarifier and push the
machine forward. Do not run with the scarifier, walk
at a constant speed that allows the machine to scarify
the lawn.
7.2. ADJUSTING THE CUTTING HEIGHT
Attention! Stop the machine and wait for the blade
to stop before adjusting the height adjustment. The
blades need a few moments to stop completely after
stopping the engine.
To regulate the height adjustment, press the lever
outwards and move it or up or down to the desired
spot.
If you regulate the height between 0 and 5mm, only
the springs will sink on the soil and the aeration will
take place.
If you regulate the height between 5mm and 10mm,
the springs and the blades will enter the soil and then
you will be scarifying.
7.3. CUTTING WITH THE SCARIFIER
Place the scarifier in one corner of the working area
and adjust the cutting height adjustment to the
desired place.
Check that the catcher is correctly placed, check that
the blade is not in contact with any object and start
the scarifier.
Walk at a pace that allows the scarifier to work
correctly.
Empty the catcher when full. When emptying the
catcher, always turn the machine off and ensure that
the blade has stopped before removing the catcher.
If you have to transport the machine between two
working areas, always switch off the machine before
transporting.
Summary of Contents for GARLAND SCAR 302 E
