background image

CI6SE3 60cm Induction Cooktop  

Page 12 

Locking the controls 

 

                        

•  You can lock the controls to prevent unintended use (for example accidentally 
turning the cooking zones on).

• When the controls are locked, all the controls except the ON/OFF control are 
disabled.

To lock the controls

Touch the keylock  

 control. The timer indicator will show “Lo “.

To unlock the controls

1. Make sure the cooktop is turned on.

2. Touch and hold the keylock  

 control for 3 seconds.

3. You can now start using your cooktop.

When the cooktop is in lock mode, all the controls are disabled except 
the ON/OFF, you can always turn the cooktop off with the ON/OFF 
control in an emergency, but you shall unlock the cooktop first in the 
next operation.

Residual Heat Indication

When the cooktop has been operating for some time, there will be some 
residual heat. The letter “H” appears to warn you to keep away from it.

                                                         

Auto Shutdown

                                                      

Safety feature of the cooktop is auto shut down. This occurs whenever you 
forget to switch off a cooking zone. The default shutdown times are shown in 
the table below:

Power level

1

2

3

4

5

6

7

8

9

Default shutdown time (hours)

8

8

8

4

4

4

2

2

2

Summary of Contents for CI6SE3





























Reviews: